Researchers employ foot-mounted inertial measurement units (IMUs) to estimate the three-dimensional trajectory of the feet as well as a rich array of gait parameters. However, the accuracy of those estimates depends critically on the limitations of the accelerometers and angular velocity gyros embedded in the IMU design. In this study, we reveal the effects of accelerometer range, gyro range, and sampling frequency on gait parameters (e.g., distance traveled, stride length, and stride angle) estimated using the zero-velocity update (ZUPT) method. The novelty and contribution of this work are that it: (1) quantifies these effects at mean speeds commensurate with competitive distance running (up to 6.4 m/s); (2) identifies the root causes of inaccurate foot trajectory estimates obtained from the ZUPT method; and (3) offers important engineering recommendations for selecting accurate IMUs for studying human running. The results demonstrate that the accuracy of the estimated gait parameters generally degrades with increased mean running speed and with decreased accelerometer range, gyro range, and sampling frequency. In particular, the saturation of the accelerometer and/or gyro induced during running for some IMU designs may render those designs highly inaccurate for estimating gait parameters.
Human lower-limb kinematic measurements are critical for many applications including gait analysis, enhancing athletic performance, reducing or monitoring injury risk, augmenting warfighter performance, and monitoring elderly fall risk, among others. We present a new method to estimate lower-limb kinematics using an error-state Kalman filter that utilizes an array of body-worn inertial measurement units (IMUs) and four kinematic constraints. We evaluate the method on a simplified 3-body model of the lower limbs (pelvis and two legs) during walking using data from simulation and experiment. Evaluation on this 3-body model permits direct evaluation of the ErKF method without several confounding error sources from human subjects (e.g., soft tissue artefacts and determination of anatomical frames). RMS differences for the three estimated hip joint angles all remain below 0.2 degrees compared to simulation and 1.4 degrees compared to experimental optical motion capture (MOCAP). RMS differences for stride length and step width remain within 1% and 4%, respectively compared to simulation and 7% and 5%, respectively compared to experiment (MOCAP). The results are particularly important because they foretell future success in advancing this approach to more complex models for human movement. In particular, our future work aims to extend this approach to a 7-body model of the human lower limbs composed of the pelvis, thighs, shanks, and feet.
This study introduces a new method to understand how added load affects human performance across a broad range of athletic tasks (ten obstacles) embedded in an outdoor obstacle course. The method employs an array of wearable inertial measurement units (IMUs) to wirelessly record the movements of major body segments to derive obstacle-specific metrics of performance. The effects of load are demonstrated on (N = 22) participants who each complete the obstacle course under four conditions including unloaded (twice) and with loads of 15% and 30% of their body weight (a total of 88 trials across the group of participants). The IMU-derived performance metrics reveal marked degradations in performance with increasing load across eight of the ten obstacles. Overall, this study demonstrates the significant potential in using this wearable technology to evaluate human performance across multiple tasks and, simultaneously, the adverse effects of body-borne loads on performance. The study addresses a major need of military organizations worldwide that frequently employ standardized obstacle courses to understand how added loads influence warfighter performance. Importantly, the findings and conclusions drawn from IMU data would not be possible using traditional timing metrics used to evaluate task performance.
Inertial measurement units (IMUs) offer an attractive way to study human lower-limb kinematics without traditional laboratory constraints. We present an error-state Kalman filter method to estimate 3D joint angles, joint angle ranges of motion, stride length, and step width using data from an array of seven body-worn IMUs. Importantly, this paper contributes a novel joint axis measurement correction that reduces joint angle drift errors without assumptions of strict hinge-like joint behaviors of the hip and knee. We evaluate the method compared to two optical motion capture methods on twenty human subjects performing six different types of walking gait consisting of forward walking (at three speeds), backward walking, and lateral walking (left and right). For all gaits, RMS differences in joint angle estimates generally remain below 5 degrees for all three ankle joint angles and for flexion/extension and abduction/adduction of the hips and knees when compared to estimates from reflective markers on the IMUs. Additionally, mean RMS differences in estimated stride length and step width remain below 0.13 m for all gait types, except stride length during slow walking. This study confirms the method’s potential for non-laboratory based gait analysis, motivating further evaluation with IMU-only measurements and pathological gaits.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.