High overall pressure ratio (OPR) engine cycles for reduced NOx emissions will generate new aggravated requirements and boundary conditions by implementing low emission combustion technologies into advanced engine architectures. Lean burn combustion systems will have a significant impact on the temperature and velocity traverse at the combustor exit. Lean burn fuel injectors dominate the combustor exit conditions. This is due to the fact that they pass a majority of the total combustor flow, and to the lack of mixing jets like in a conventional combustor. With the transition to high-pressure engines, it is essential to fully understand and determine the high energetic interface between combustor and turbine to avoid excessive cooling. Velocity distributions and their fluctuations at the combustor exit for lean burn are of special interest as they can influence the efficiency and capacity of the turbine. A lean burn single-sector combustor was designed and built at DLR, providing optical access to its rectangular exit section. The sector was operated with a fuel-staged lean burn injector. Measurements were performed under idle and cruise operating conditions. Two velocity measurement techniques were used in the demanding environment of highly luminous flames under elevated pressures: particle image velocimetry (PIV) and filtered Rayleigh scattering (FRS). The latter was used for the first time in an aero-engine combustor environment. In addition to a conventional signal detection arrangement, FRS was also applied with an endoscope for signal collection, to assess its practicality for a potential future application in a full annular combustor with restricted optical access.
A rotating cooling system with a 180 deg turn is investigated experimentally using the 2C PIV technique to measure the flow inside. This cooling configuration consists of two ducts of arbitrary cross-sections representing a two-pass front part of an idealized but nevertheless engine relevant turbine blade cooling design. The system has been investigated with ribbed walls in both passages for cooling enhancement as well as with smooth walls as a reference version in order to identify the effects induced by ribs. The rib orientation on the walls is 45 deg. With a rib height of 0.1 of hydraulic duct diameter and a pitch of 10 times rib height, a representative well-established rib lay-out was selected. This paper presents measurements of the axial flow during rotation of this two-pass system for rotation numbers up to 0.1. Together with previously obtained stationary results [1], this data completes the investigation of the secondary flow field with rotational results acquired with a two-component PIV measuring technique with improved sequencer technique [2]. The Two-Pass Cooling System was analyzed on the rotating test rig using two-component Particle Image Velocimetry (2C PIV) a non-intrusive optical planar measurement technique. PIV is capable of obtaining complete flow maps of the instantaneous as well as averaged flow field even at high turbulence levels, which are typical for the narrow serpentine-shaped ribbed cooling systems. An in-house developed synchronization device enables very accurate control of the laser flashes and image acquisition with regard to the angular position of the measurement plane (light sheet) and thereby very accurately stabilizes the position of the channel within the image during PIV recording which then leads to very accurate mean velocities. The presented investigations were conducted in stationary and rotating mode. The results demonstrate the combined interaction of different vortices induced by several effects such as the inclination of ribs, Coriolis forces due to rotation and inertial forces within the bend. Additionally, a flow separation was observed at the divider wall downstream of the bend (in the second pass) that has a strong impact on the flow field depending on the rotational speed. The axial flow maps presented in this paper in combination with the secondary flow maps published previously are of sufficient high quality and spatial resolution to serve as a benchmark test case for the validation of flow solvers. The turbulent channel flow was investigated at a Reynolds number of 50,000 and at rotation numbers of 0.0 and 0.1.
The flow field characteristics of a two-pass cooling system with an engine-similar lay-out have been investigated experimentally using the non-intrusive Particle Image Velocimetry (PIV). It consists of a trapezoidal inlet duct, a nearly rectangular outlet duct, and a sharp 180 degree turn. The system has been investigated with smooth and ribbed walls. Ribs are applied on two opposite walls in a symmetric orientation inclined with an angle of 45 degrees to the main flow direction. The applied rib lay-out is well-proved and optimized with respect to heat transfer improvement versus pressure drop penalty. The system rotates about an axis orthogonal to its centreline. The configuration was analyzed with the planar two-component PIV technique (2C PIV), which is capable of obtaining complete maps of the instantaneous as well as the averaged flow field even at high levels of turbulence, which are typically found in sharp turns, in ribbed ducts and, especially, in rotating ducts. In the past, slip between motor and channel rotation causes additional not negligible uncertainties during PIV measurements due to unstable image position. These were caused by the working principle of the standard programmable sequencer unit used in combination with unsteady variations of the rotation speed. Therefore, a new sequencer was developed using FPGA-based hardware and software components from National Instruments which revealed a significant increase of the stability of the image position. Furthermore, general enhancements of the operability of the PIV system were achieved. The presented investigations of the secondary flow were conducted in stationary and, with the new sequencer technique applied, in rotating mode. Especially in the bend region vortices with high local turbulence were found. The ribs also change the fluid motion as desired by generating additional vortices impinging the leading edge of the first pass. The flow is turbulent and isothermal, no buoyancy forces are active. The flow was investigated at Reynolds number of Re = 50,000, based on the reference length d (see Fig. 3). The rotation number is Ro = 0 (non-rotating) and 0.1. Engine relevant rotation numbers are in order of 0.1 and higher. A reconstruction of some test rig components, especially the model mounting, has become necessary to reach higher values of the rotational speed compared to previous investigations like in Elfert [2008]. This investigation is aimed to analyze the complex flow phenomena caused by the interaction of several vortices, generated by rotation, flow turning or inclined wall ribs. The flow maps obtained with PIV are of good quality and high spatial resolution and therefore provide a test case for the development and validation of numerical flow simulation tools with special regard to prediction of flow turbulence under rotational flow regime as typical for turbomachinery. Future work will include the investigation of buoyancy effects to the rotational flow. This implicates wall heating which result from the heater glass in order to provide transparent models.
The flow field characteristics of a two-pass cooling system with an engine-similar layout have been investigated experimentally using the nonintrusive particle image velocimetry (PIV). It consists of a trapezoidal inlet duct, a nearly rectangular outlet duct, and a sharp 180 deg turn. The system has been investigated with smooth and ribbed walls. Ribs are applied on two opposite walls in a symmetric orientation inclined with an angle of 45 deg to the main flow direction. The applied rib layout is well proven and optimized with respect to heat transfer improvement versus pressure drop penalty. The system rotates about an axis orthogonal to its centerline. The configuration was analyzed with the planar two-component PIV technique, which is capable of obtaining complete maps of the instantaneous as well as the averaged flow field even at high levels of turbulence, which are typically found in sharp turns, in ribbed ducts, and, especially, in rotating ducts. In the past, a slip between motor and channel rotation causes additional non-negligible uncertainties during PIV measurements due to an unstable image position. These were caused by the working principle of the standard programmable sequencer unit used in combination with unsteady variations in the rotation speed. Therefore, a new sequencer was developed using FPGA-based hardware and software components from National Instruments (NI), which revealed a significant increase in the stability of the image position. Furthermore, general enhancements of the operability of the PIV system were achieved. The presented investigations of the secondary flow were conducted in stationary and, with the new sequencer technique applied, in rotating mode. Especially in the bend region, vortices with high local turbulence were found. The ribs also change the fluid motion as desired by generating additional vortices impinging the leading edge of the first pass. The flow is turbulent and isothermal; no buoyancy forces are active. The flow was investigated at a Reynolds number of Re=50,000, based on the reference length d (see Fig. 3). The rotation numbers are Ro=0.0 (nonrotating) and 0.1. Engine relevant rotation numbers are in order of 0.1 and higher. A reconstruction of some test rig components, especially the model mounting, has become necessary to reach higher values of the rotational speed compared with previous investigations such as the work of Elfert et al. (2008, “Detailed Flow Investigation Using PIV in a Rotating Square-Sectioned Two-Pass Cooling System With Ribbed Walls,” ASME Turbo Expo, Berlin, Germany, Jun. 9–13, Paper No. GT-2008-51183). This investigation is aimed to analyze the complex flow phenomena caused by the interaction of several vortices, generated by rotation, flow turning, or inclined wall ribs. The flow maps obtained with PIV are of good quality and high spatial resolution and therefore provide a test case for the development and validation of numerical flow simulation tools with special regard to the prediction of flow turbulence under the rotational flow regime, which is typical of turbomachinery. Future work will include the investigation of buoyancy effects to the rotational flow. This implicates wall heating, which results from the heater glass in order to provide transparent models.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.