We explored factors influencing hydroxyl radical (•OH) formation during ozonation of multiwalled carbon nanotubes (MWCNTs) and assessed this system's viability as a next-generation advanced oxidation process (AOP). Using standard reactivity metrics for ozone-based AOPs (RCT values), MWCNTs promoted •OH formation during ozonation to levels exceeding ozone (both alone and with activated carbon) and equivalent to ozone with hydrogen peroxide. MWCNTs oxidized with nitric acid exhibited vastly greater rates of ozone consumption and •OH formation relative to as-received MWCNTs. While some of this enhancement reflects their greater suspension stability, a strong correlation between RCT values and surface oxygen concentrations from X-ray photoelectron spectroscopy suggests that surface sites generated during MWCNT oxidation promote •OH exposure. Removal of several ozone-recalcitrant species [para-chlorobenzoic acid (p-CBA), atrazine, DEET, and ibuprofen] was not significantly inhibited in the presence of radical scavengers (humic acid, carbonate), in complex aquatic matrices (Iowa River water) and after 12 h of continuous exposure of MWCNTs to concentrated ozone solutions. As a proof-of-concept, oxidized MWCNTs deposited on a ceramic membrane chemically oxidized p-CBA in a flow through system, with removal increasing with influent ozone concentration and mass of deposited MWCNTs (in mg/cm2). This hybrid membrane platform, which integrates adsorption, oxidation, and filtration via an immobilized MWCNT layer, may serve as the basis for future novel nanomaterial-enabled technologies, although long-term performance trials under representative treatment scenarios remain necessary.

Titanium dioxide (TiO2) nanofibers with tailored structure and composition were synthesized by electrospinning to optimize photocatalytic treatment efficiency. Nanofibers of controlled diameter (30-210 nm), crystal structure (anatase, rutile, mixed phases), and grain size (20-50 nm) were developed along with composite nanofibers with either surface-deposited or bulk-integrated Au nanoparticle cocatalysts. Their reactivity was then examined in batch suspensions toward model (phenol) and emerging (pharmaceuticals, personal care products) pollutants across various water qualities. Optimized TiO2 nanofibers meet or exceed the performance of traditional nanoparticulate photocatalysts (e.g., Aeroxide P25) with the greatest reactivity enhancements arising from (i) decreasing diameter (i.e., increasing surface area), (ii) mixed phase composition [74/26 (±0.5) % anatase/rutile], and (iii) small amounts (1.5 wt %) of surface-deposited, more so than bulk-integrated, Au nanoparticles. Surface Au deposition consistently enhanced photoactivity by 5- to 10-fold across our micropollutant suite independent of their solution concentration, behavior that we attribute to higher photocatalytic efficiency from improved charge separation. However, the practical value of Au/TiO2 nanofibers was limited by their greater degree of inhibition by solution-phase radical scavengers and higher rate of reactivity loss from surface fouling in nonidealized matrixes (e.g., partially treated surface water). Ultimately, unmodified TiO2 nanofibers appear most promising for use as reactive filtration materials because their performance was less influenced by water quality, although future efforts must increase the strength of TiO2 nanofiber mats to realize such applications.

No abstract

No abstract

No abstract

Lead telluride (PbTe) nanofibers were fabricated by galvanic displacement of electrospun cobalt nanofibers where their composition and morphology were altered by adjusting the electrolyte composition and diameter of sacrificial cobalt nanofibers. By employing Co instead of Ni as the sacrificial material, residue-free PbTe nanofibers were synthesized. The Pb content of the PbTe nanofibers was slightly affected by the Pb2+ concentration in the electrolyte, while the average outer diameter increased with Pb2+ concentration. The surface morphology of PbTe nanofibers was strongly dependent on the diameter of sacrificial nanofibers where it altered from smooth to rough surface as the Pb2+ concentration increased. Some of thermoelectric properties [i.e., thermopower (S) and electrical conductivity(σ)] were systematically measured as a function of temperature. Energy barrier height (Eb) was found to be one of the key factors affecting the thermoelectric properties–that is, higher energy barrier heights increased the Seebeck coefficient, but lowered the electrical conductivity.

No abstract

No abstract