The synthesis of cyclic carbonates through coupling of carbon dioxide with epoxides is 100 % atom economical and is already performed on an industrial scale. Its impact regarding the use of carbon dioxide as a renewable carbon source is expected to grow significantly in the near future, so that the development of efficient catalysts is of high interest in academia and industry. To improve the carbon footprint and sustainability of the cycloaddition reaction, the use of organocatalytic methods is a promising approach. Herein, available metal-free catalysts for the preparation of cyclic carbonates are described and elaborated concerning the overall sustainability of the process. Therefore, the required reaction conditions, as well as the activity of the catalysts and their reusability, are compared and evaluated. In addition to ammonium-, phosphonium-, or imidazolium-based single-component catalysts and their supported analogues, the growing field of research concerning dual catalysts are also discussed in detail.

The combination of pentaerythritol with nucleophilic halide salts such as nBu4NI is used as a dual catalyst system for the cycloaddition of carbon dioxide (CO2) with a broad range of organic epoxides yielding the respective cyclic carbonates. Due to synergistic effects of the organocatalysts, excellent yields and selectivities could be achieved under mild reaction conditions. Moreover, the nontoxic, cost-efficient, and readily available system is easily recyclable without significant loss of reactivity, representing an exceptional sustainable approach for the fixation of CO2.

Hydroxy‐functionalized mono‐ and bisimidazolium bromides were synthesized and applied as catalysts for the cycloaddition of CO2 and epoxides to cyclic carbonates. A catalyst screening showed the influence of the number of protic hydrogen atoms at the cation for the activation of epoxides. The most active catalyst operates at very mild reaction conditions (70 °C, 0.4 MPa CO2) and can be easily recycled ten times without loss of activity.

No abstract

Hydrophobic imidazolium-based ionic liquids (IL) act as catalysts for the epoxidation of unfunctionalized olefins in water using hydrogen peroxide as oxidant. Although the catalysts are insoluble in both the substrate and in water, surprisingly, they are very well soluble in aqueous H2 O2 solution, owing to perrhenate-H2 O2 interactions. Even more remarkably, the presence of the catalyst also boosts the solubility of substrate in water. This effect is crucially dependent on the cation design. Hence, the imidazolium perrhenates enable both the transfer of hydrophobic substrate into the aqueous phase, and serve as actual catalysts, which is unprecedented. At the end of the reaction and in absence of H2 O2 the IL catalyst forms a third phase next to the lipophilic product and water and can easily be recycled.

Imidazolium bromides combined with niobium(v) choride were used as catalyst system for the reaction of CO2 with epoxides to cyclic carbonates. The variation of the cation structure strongly affects the properties of the imidazolium salt and therefore the catalytic activity.

The activated anionic ring opening polymerization of ε-caprolactam to polyamide 6 is highly sensitive to external influences such as water. Based on an initial theory, preliminary reaction kinetic tests are carried out with the aim of compensating the influence of the water by increasing the activator and catalyst concentration. Different formulations of activator and catalyst were studied to understand the influence of water on the concentration of activator and catalyst. It was found that the compensation of added water with activator and catalyst restores the original reaction time. The test plates produced are examined with regard to their mechanical characteristics and the polymer properties. The results of the mechanical characterization show no significant impairment after compensation of the added water. The physical properties of the matrix show degradation with repeated compensation. However, the residual ε-caprolactam content remains below the critical value of 1% for three of the four investigated formulations.

The reaction kinetics of anionic polymerization for the production of anionic polyamide 6 (aPA6) are widely understood. It is also known that this reaction is very sensitive to external influences such as water. This paper analyzes and quantifies the influence of water on the reaction of ε-caprolactam to anionic polyamide 6. A kinetic model is developed in which the reactive molecules of the activator and catalyst are defined as variables and the concentrations of activator and catalyst as well as water content are considered. A model for the calculation of the reaction kinetics is established and validated with experimental data. The developed model can be used to predict the influence and compensation of water by addition of surplus activator and catalyst during the polymerization of ε-caprolactam.