No abstract

Background/objectives Disinfection of surgical guides is mandatory for intraoperative use. Virgin Coconut Oil may be a potent alternative disinfectant; however, its effect has not been fully discussed in dentistry. The objectives of this study were to compare the morphological and the volumetric dimensional changes of 3D printed surgical guides after immersion in three disinfectants: 100%Virgin Coconut Oil, 2% Glutaraldehyde, and 70% Ethyl Alcohol and to assess the antimicrobial effectiveness of the tested disinfectants. Materials and methods A surgical guide was designed using open platform software to print thirty guides and then cut them into two halves (N = 60). Pre-disinfection scans of the first half of the three study groups (n = 30) were performed using Cone-beam Computed Tomography, then immersed for 20 min in three disinfectants as follows: group VCO was immersed in 100% Virgin Coconut Oil, group GA was immersed in 2% Glutaraldehyde, and group EA was immersed in 70% Ethyl Alcohol. Post-disinfection scans of the first half of the three study groups (n = 30) were performed and then compared morphologically and volumetrically using an analyzing software program The second half of the three control groups (n* = 30) were soaked for 20 min in sterile distilled water as follows: group VCO*, group GA*, and group EA* for the assessment of the antimicrobial effectiveness of the three tested disinfectants. Results At the morphological assessment of the dimensional changes, group VCO were the most accurate with the lowest mean deviation value of 0.12 ± 0.02 mm and root mean square value of 0.12 mm, group GA and group EA were less accurate with mean deviation value of = 0.22 ± 0.05 mm and = 0.19 ± 0.03 mm and root mean square value of 0.22 and 0.20 respectively (p < 0.001). At the volumetric assessment, group VCO showed lower volumetric changes with a mean deviation value of 0.17 ± 0.10 mm, root mean square value of 0.19 mm, than group GA with mean deviation value of 0.23 ± 0.10 mm, root mean square value of 0.25 mm and group EA with mean deviation value of 0.27 ± 0.11 mm, root mean square value of 0.29 mm, however, no statistically significant differences were found between the three study groups (p = 0.10). The antimicrobial effectiveness of the three tested disinfectants showed a hundred percent (100%) reduction in the total microbial count in the first half of the three study groups treated with the three disinfectants revealing no bacterial growth, however, statistically significant differences were found between the second half of the three control and the first half of the three study groups. (p < 0.001). Conclusions Virgin Coconut Oil showed higher morphological dimensional accuracy of the tested surgical guides than Glutaraldehyde and Ethyl Alcohol without causing any volumetric dimensional changes in the 3D printed surgical guides after disinfection for 20 min and the antimicrobial effectiveness was the same between the three tested disinfectants without showing any microbial growth.

Background/objective Disinfection of a 3D-printed surgical guide is of utmost importance as it comes into contact with hard and soft tissue during implant placement so it poses a potential risk of pathogenic transmission. Methods used for disinfection in the surgical field should be reliable, practical, and safe for the instruments and the patients. The objectives of this study were to compare the antimicrobial potential of 100% Virgin Coconut Oil, 2% Glutaraldehyde, and 70% Ethyl Alcohol used to decontaminate 3D-printed surgical guides. Materials and methods Thirty identical surgical guides were printed and cut into two halves (N = 60). Both halves were then contaminated with a defined amount of human saliva samples (2 ml). The first half (n = 30) was sub-grouped into three study groups which were immersed in one of the three disinfectants for 20 min as follows; group VCO was immersed in 100% Virgin Coconut Oil, group GA was immersed in 2% Glutaraldehyde, and group EA was immersed in 70% Ethyl Alcohol. The second half (n* = 30) was sub-grouped into three control groups which were immersed in sterile distilled water as follows group VCO*, group GA*, and group EA*. The microbial count was expressed as colony-forming units per plate and the comparison of the antimicrobial potential of the three tested disinfectants between the three study and three control groups was done using the One-Way ANOVA test. Results The culture results of three study groups revealed no bacterial growth with the highest % of reduction in the mean microbial count of the oral microorganisms (about100%) and an uncountable bacterial growth was shown between the three control groups (more than 100 CFU/plate) representing the baseline of the oral microorganisms. Therefore; statistically significant differences were found between the three control and three study groups (P < .001). Conclusion The antimicrobial potential of Virgin Coconut Oil was comparable and equivalent to Glutaraldehyde and Ethyl Alcohol with a significant inhibitory action against oral pathogens.

Statement of the problem: Designing of removable partial denture (RPD) present numerous biomechanical problems regarding the principles of reciprocation. However, extra coronal resilient attachment does not always supply suitable support and bracing because of their resilient nature. Therefore, they require specially designed bracing arms on surveyed crowns that require deeper tooth preparation lingually to prevent over contouring of the abutment teeth crown. Purpose of the study: The aim of this study was to evaluate clinically and radiographically the extra coronal semi precision attachments incorporated in metallic (RPD) with two different designs of reciprocation; parallel interlock and integrated interlock. Materials and methods:Six patients were selected for this study having maxillary completely dentulous arch against mandibular bilateral distal extension ridges posterior to second premolar. All attachment clinical and laboratory steps were performed for both designs using Split-mouth experimental method. Abutment teeth were examined clinically using; Plaque Index, Gingival Index, Periodontal Probing Pocket Depth and Clinical Attachment Level and radiographically immediately at time of RPD insertion then 3, 6 months of denture use. Results:Clinical results showed statistically significant increase in all parameters around parallel interlock design than integrated interlock design after six months. There was statistically significant increase in total mesial and distal bone loss associated with parallel interlock design in relation to integrated interlock design at six months follow up period. Conclusions: Absence of lingual bracing arm with integrated interlock design decreased the opportunity for plaque accumulation and enhanced the oral health of the premolar abutment teeth. Clinical implications:This study recommends the use of integrated interlock design for reciprocation as a common design of extracoronal semiprecision attachment for distal extension RPD for its favorable intraoral health parameters.

Various techniques have been described for the rehabilitation of ocular defects with ocular prostheses to restore lost anatomical structures and correct cosmetic defects. This article describes a technique for optimizing the position of an iris disk over a custom‐made ocular prosthesis, by using eyeglasses with customized graph paper pattern lenses. It presents a simplified method that will be useful for people with ocular defects in remote and distant service areas with limited resources.

Background: Although 3D printed photoinitiated resins are among the many materials utilized in prosthetic appliances today, biocompatibility for photocuring 3D printing materials for direct and long-term contacting with living body remain scarce. The purpose of this in vitro study was to evaluate the cell viability of human gingival fibroblasts after the exposure to two different 3D printed photoinitiated resins and compare it to the traditionally used heat polymerized acrylic resin for up to 7 days.Methods: This comparative in vitro study of sample size (n= 96), where the 3D printed resin disc samples (n= 64), were divided into two test groups, test group 1 (TG1) for NextDent Base resin (n= 32) and test group 2 (TG2) for Dental LT clear resin (n= 32), to be compared to Heat polymerized acrylic resin samples (Reference group (RG)) (n= 32). Human gingival fibroblasts were extracted from attached keratinized gingival tissues collected from healthy patient undergoing clinical crown lengthening procedure, cellular viability using MTT assay in response to TG1, TG2 and RG samples was assessed throughout four-time intervals (24, 48, 72 and 168 hours). The One-Way ANOVA test followed by Tukey’s post hoc test and Repeated Measures ANOVA test were used for statistical analyses, statistically significant different at P value ≤ 0.05Results: Throughout time intervals, there was a decrease in cell viability of all groups but with favorable cell viability which was more that 90% denoting non cytotoxicity. It was found to be significant among RG (P< 0.0001). The highest cell viability was found after 24 hours among all groups; however, the least viability was found after 48 hours among TG1 and RG, and among TG2 after 72 hours. After 168 hours, there was a non-statistical significant change in cell viability between groups (P= 0.526). there was significant increase in optical density for all groups throughout time intervals (P< 0.0001).Conclusion: Photoinitiated resins are comparable to traditionally used heat polymerized acrylic resin with equivalent cytotoxic effect for long term use. 3D printed photoinitiated resins are biocompatible and suggested for long term intraoral use.