ÖzetMobilya endüstrisinde, çerçeve ve kutu konstrüksiyonlu mobilyaların birleştirme noktalarının kullanım yeri etkisinde kalacak yüklere göre tasarlanması kullanıcının güvenliği ve mobilya elemanın servis ömrü açısında önem arz etmektedir. Bu önemden yola çıkarak, masif ahşap malzemelerden hazırlanan kutu konstrüksiyonlu mobilyaların "L" tipi köşe birleştirmelerinin diyagonal basma ve diyagonal çekme eğilme moment değerlerinin belirlenmesi amaçlanmıştır. Bu amaca ulaşmak için Karaçam (Pinus Nigra), Doğu Kayın'ı (Fagus Orientalis L.) ve Kavak (Populus Nigra) masif ahşap malzemelerden kutu tipi konstrüksiyonlar oluşturulmuştur. Deney konstrüksiyonun köşe birleştirmelerinde odun esaslı bisküvi birleştirme elemanı ve yapıştırıcı olarak epoksi reçinesi kullanılmıştır. Deney ASTM-D1037 esaslarına göre statik yükleme uygulanmıştır. Deney sonuçlarına göre; çekme ve basma deneylerinde en yüksek eğilme moment değeri Doğu kayını örneklerinde, en düşük değerin ise Kavak örneklerinde olduğu belirlenmiştir. Araştırmada çekme eğilme momenti değerleri basma eğilme momenti değerlerinden yüksek çıkmıştır. Yapılan istatistik çalışmasında, bisküvi birleştirme elemanının çekme ve basma eğilme moment değerleri arasındaki farklılık istatistiksel olarak anlamlı bulunmuştur. Araştırmanın sonuçları doğrultusunda, Epoksi reçinesi ve odun esaslı bisküvi birleştirme elemanı kullanarak Doğu Kayınından hazırlanan L tipi birleştirmelerin çerçeve kontstrüksiyonlarda kullanımı önerilebilir. AbstractIn the furniture industry, the joining points of frame and box construction furniture according to the loads to be affected by the use place is important for the security of the user and service life of the furniture element. In this direction, it is aimed to determine the diagonal compression and diagonal tensile moment values of "L" type corner joints of box framed construction furniture prepared from solid wood materials. The Pinus Nigra, Fagus Orientalis L and Populus Nigra were used as solid wood materials. Wood-based biscuit joining elements were used in corner joints of the test construction and epoxy resin was used as glue for materials. The static loads were applied to construction according to ASTM-D1037. The results show that, the highest tensile and compression values were obtained from Fagus Orientalis L and the lowest values were obtained from Populus Nigra specimens. In the statistical study, the difference between the tensile and compressive bending moment values of the biscuit connection element was found to be statistically significant. This study indicates that, it is suggested to use of L type joints prepared from Fagus Orientalis L by using epoxy resin and wood based biscuit joining element in frame constructions.
The purpose of this study is to determine the effects of the nano-particulate silicon dioxide (SiO2) material on the bending strength and modulus of elasticity in bending of some wood species. Oriental beech (Fagus orientalis L.) and sessile oak (Quercus petrea L.) woods species which are commonly used in the furniture industry were used in this study. Impregnation was carried out with the preparation of SiO2 at concentrations of 1% and 3% according to ASTM-D 1413ASTM-D -76 (1976 standards. According to the results, while solution concentration was increasing in both wood species, total retention (kg/m 3 ) and percentage retention (%) values increased; air dry density (12%), bending strength and modulus of elasticity in bending decreased. The maximum mean values of bending strength and modulus of elasticity was in control samples of oriental beech and the minimum were in sessile oak wood with 3% concentration. These results can be related to the fact that the higher density of oriental beech wood (0.630-0.685 g/cm³). In both species of wood, impregnation with SiO2 resulted loss of about 3-5% in bending strength and 0.6-9% in modulus of elasticity.
Mobilya köşe birleştirmelerinde demonte tipi bağlantı elemanlarının moment kapasitesine etkileri The effects of disassembled type connection elements moment capacity in furniture corner joints
Double haploid (DH) teknolojisi son yıllarda gelişmiş ıslah programlarında yaygın olarak kullanılan bir araç haline gelmiştir.Mısır ıslahında in vivo double-haploid yöntemiyle saf hat elde etme, ıslahta zaman ve maliyet yönünden büyük avantaj sağlamakta ve ıslah süresini 6 yıl kadar kısaltmaktadır. Ayrıca daha fazla kendilenmiş hattın kolayca elde edilmesi ıslahtan elde edilecek başarı oranını artırmaktadır. Double-haploid saf hatlar %100 homozigot olmaları nedeniyle konvansiyonel yöntemle elde edilmiş kendilenmiş hatlara kıyasla daha yüksek genetik stabiliteye sahiptirler.Araştırmada maternal in vivo double-haploid yönteminin yukarıda sayılan avantajlarından faydalanılması hedeflenmiş ve haploid tohumlara kromozom katlaması tekniği başarıyla uygulanmıştır. DH tekniği ile geliştirilen n kromozomlu 12 adet haploid genotip, 2019 yılında Dicle Üniversitesi Ziraat Fakültesi Tarla Bitkileri bölümüne ait laboratuvar, bitki yetiştirme kabini ve sera koşullarında incelenmiştir. Çalışmada kullanılan 12 genotipte kromozom katlanma işlemi başarıyla gerçekleştirilmiş ve bu genotiplere ait bazı agronomik özellikler incelenmiştir. Kendilenmiş double-haploid bitkilerde incelenen agronomik özellikler neticesinde DZM-45 ve DZM-7 genotiplerinin diğer hatlara üstünlük sağlayarak kendilenmiş hat olabilme potansiyelinde olduğu gözlemlenmiştir.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.