In the present work, densification and microstructure evolution of cobalt ferrite (FCO), nickel-cobalt ferrite (FNICO) and BaTiO3 (TB) ceramics under different sintering conditions were investigated. Subsequently, layered ferrite-BaTiO3 samples were formed by uniaxial pressing of the corresponding ceramic powders. These green samples were sintered with two different sintering schedules, aiming to study the ferrite-BaTiO3 interfaces after sintering. The analyses were made at the cross section of the interfaces and at the interface surfaces after separation of the layers. The sintered layered samples were utilized to analyze sintering mismatch, diffusion at the interfaces and identification of some newly formed phases. EDS analysis across the TB-FCO interface showed evidences of diffusion. It was observed that the FNICO layers were detached from TB during sintering, but the same was not observed in the TB-FCO samples, although shrinkage mismatch resulted in some defects. XRD analyses suggested the presence of Ti2O at the TB-FCO interface and BaTiNiFe10O19 at the TB-FNICO interface as products of the reactions between the ferrites and BaTiO3.
Editora Direitos para esta edição cedidos à Atena Editora pelos autores. Open access publication by Atena Editora Todo o conteúdo deste livro está licenciado sob uma Licença de Atribuição Creative Commons. Atribuição-Não-Comercial-NãoDerivativos 4.0 Internacional (CC BY-NC-ND 4.0). O conteúdo dos artigos e seus dados em sua forma, correção e confiabilidade são de responsabilidade exclusiva dos autores, inclusive não representam necessariamente a posição oficial da Atena Editora. Permitido o download da obra e o compartilhamento desde que sejam atribuídos créditos aos autores, mas sem a possibilidade de alterála de nenhuma forma ou utilizá-la para fins comerciais.Todos os manuscritos foram previamente submetidos à avaliação cega pelos pares, membros do Conselho Editorial desta Editora, tendo sido aprovados para a publicação com base em critérios de neutralidade e imparcialidade acadêmica.A Atena Editora é comprometida em garantir a integridade editorial em todas as etapas do processo de publicação, evitando plágio, dados ou resultados fraudulentos e impedindo que interesses financeiros comprometam os padrões éticos da publicação. Situações suspeitas de má conduta científica serão investigadas sob o mais alto padrão de rigor acadêmico e ético.
ResumoAtualmente as propriedades microestruturais da ferrita de cobalto são bem conhecidas, e as suas vantagens em relação á outros materiais como o baixo custo e a resistência á corrosão, nos remete a analisar efeitos que podem ocorrer na microestrutura do material devido a mudanças nas condições de processamento. O objetivo deste trabalho é estudar as características do pó de CoFe2O4 nas diferentes etapas do processamento cerâmico em moinho excêntrico e o efeito da variação da temperatura de calcinação (750°C, 850°C e 950°C) na microestrutura de amostras sinterizadas a 1.300°C/2h. Portanto, serão analisados em MEV (microscópio eletrônico de varredura) a mistura dos óxidos de cobalto e óxido de ferro sem calcinação, os pós com variação da temperatura de calcinação, um dos pós calcinados que sofrerá uma moagem, e amostras no formato de pastilhas compactadas com os pós nas diferentes condições de calcinação e, posteriormente, sinterizadas. Assim, além de alcançar o objetivo do trabalho, podemos analisar a eficiência das etapas realizadas no processamento cerâmico que utilizamos e consolidar os conhecimentos obtidos na literatura e nos procedimentos experimentais seguidos pelo grupo. Palavras-chave: Ferritas; CoFe2O4; Análise microestrutural; Cerâmicas magnéticas. Abstract Currently the microstructural properties of cobalt ferrite are well known, and its advantages over other materials such as low cost and corrosion resistance, leads us to analyze effects that may occur in the microstructure of the material due to changes in processing conditions. The objective of this work is to study the characteristics of CoFe2O4 powder in different stages of ceramic processing in eccentric mill and the effect of the variation of calcination temperature (750°C, 850°C and 950°C) on the microstructure of samples sintered at 1,300°C/2h. Therefore, be analyzed by SEM (scanning electron microscope) the mixture of the oxides of cobalt and iron oxide without calcination, the powders with variation of the calcination temperature of the calcined powders suffer a grind, and samples of the compacted pellets format with the powders at different calcination conditions and subsequently sintered. Thus, in addition to achieving the objective of the work, we analyze the efficiency of the steps performed in ceramic processing we use and consolidate knowledge from the literature and experimental procedures followed by the group.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.