Airborne measurements of methane emissions from oil and gas infrastructure were completed over two regions of Alberta, Canada. These top-down measurements were directly compared with region-specific bottom-up inventories that utilized current industry-reported flaring and venting volumes (reported data) and quantitative estimates of unreported venting and fugitive sources. For the 50 × 50 km measurement region near Red Deer, characterized by natural gas and light oil production, measured methane fluxes were more than 17 times greater than that derived from directly reported data but consistent with our region-specific bottom-up inventory-based estimate. For the 60 × 60 km measurement region near Lloydminster, characterized by significant cold heavy oil production with sand (CHOPS), airborne measured methane fluxes were five times greater than directly reported emissions from venting and flaring and four times greater than our region-specific bottom up inventory-based estimate. Extended across Alberta, our results suggest that reported venting emissions in Alberta should be 2.5 ± 0.5 times higher, and total methane emissions from the upstream oil and gas sector (excluding mined oil sands) are likely at least 25-50% greater than current government estimates. Successful mitigation efforts in the Red Deer region will need to focus on the >90% of methane emissions currently unmeasured or unreported.

Flaring is a technique used extensively in the oil and gas industry to burn unwanted flammable gases. Oxidation of the gas can preclude emissions of methane (a potent greenhouse gas); however, flaring creates other pollutant emissions such as particulate matter (PM) in the form of soot or black carbon (BC). Currently available PM emission factors for flares were reviewed and found to be questionably accurate, or based on measurements not directly relevant to open-atmosphere flares. In addition, most previous studies of soot emissions from turbulent diffusion flames considered alkene or alkyne based gaseous fuels, and few considered mixed fuels in detail and/or lower sooting propensity fuels such as methane, which is the predominant constituent of gas flared in the upstream oil and gas industry. Quantitative emission measurements were performed on laboratory-scale flares for a range of burner diameters, exit velocities, and fuel compositions. Drawing from established standards, a sampling protocol was developed that employed both gravimetric analysis of filter samples and real-time measurements of soot volume fraction using a laser-induced incandescence (LII) system. For the full range of conditions tested (burner inner diameter [ID] of 12.7-76.2 mm, exit velocity 0.1-2.2 m/sec, 4-and 6-component methane-based fuel mixtures representative of associated gas in the upstream oil industry), measured soot emission factors were less than 0.84 kg soot/10 3 m 3 fuel. A simple empirical relationship is presented to estimate the PM emission factor as a function of the fuel heating value for a range of conditions, which, although still limited, is an improvement over currently available emission factors.Implications: Despite the very significant volumes of gas flared globally and the requirement to report associated emissions in many jurisdictions of the world, a review of the very few existing particulate matter emission factors has revealed serious shortcomings sufficient to suggest that estimates of soot production from flares based on current emission factors should be interpreted with caution. New BC emissions data are presented for laboratory-scale flares in what are believed to be the first such experiments to consider fuel mixtures relevant to associated gas compositions. The empirical model developed from these data is an important step toward being able to better predict and manage BC emissions from flaring.

No abstract

No abstract

A novel, standardized geometry of the human nasal cavity was created by aligning and processing 30 sets of computed tomography (CT) scans of nasal airways of healthy subjects. Digital three-dimensional (3-D) geometries of the 60 single human nasal cavities (30 right and 30 mirrored left cavities) were generated from the CT scans and measurements of physical parameters of each single nasal cavity were performed. A methodology was developed to scale, orient, and align the nasal geometries, after which 2-D digital coronal cross-sectional slices were generated. With the use of an innovative image processing algorithm, median cross-sectional geometries were created to match median physical parameters while retaining the unique geometric features of the human nasal cavity. From these idealized 2-D images, an original 3-D standardized median human nasal cavity was created. This new standardized geometry was compared against the original geometries of all subjects as well as limited existing data from the literature. The new model has potential for use as a geometric standard in future experimental and numerical studies of deposition of inhaled aerosols, as well as for use as a reference during diagnosis of unhealthy patients. The specific procedure developed could also be applied to build standard nasal geometries for different identifiable groups within the larger population.