Denture fractures are common in daily practice, causing inconvenience to the patient and to the dentists. Denture repairs should have adequate strength, dimensional stability and color match, and should be easily and quickly performed as well as relatively inexpensive.ObjectiveThe aim of this study was to evaluate the flexural strength of acrylic resin repairs processed by different methods: warm water-bath, microwave energy, and chemical polymerization.Material and methodsSixty rectangular specimens (31x10x2.5 mm) were made with warm water-bath acrylic resin (Lucitone 550) and grouped (15 specimens per group) according to the resin type used to make repair procedure: 1) specimens of warm water-bath resin (Lucitone 550) without repair (control group); 2) specimens of warm water-bath resin repaired with warm water-bath; 3) specimens of warm water-bath resin repaired with microwave resin (Acron MC); 4) specimens of warm water-bath resin repaired with autopolymerized acrylic resin (Simplex). Flexural strength was measured with the three-point bending in a universal testing machine (MTS 810 Material Test System) with load cell of 100 kgf under constant speed of 5 mm/min. Data were analyzed statistically by Kruskal-Wallis test (p<0.05).ResultsThe control group showed the best result (156.04±1.82 MPa). Significant differences were found among repaired specimens and the results were decreasing as follows: group 3 (43.02±2.25 MPa), group 2 (36.21±1.20 MPa) and group 4 (6.74±0.85 MPa).ConclusionAll repaired specimens demonstrated lower flexural strength than the control group. Repairs with autopolymerized acrylic resin showed the lowest flexural strength.
The addition of sodium hypochlorite in both dilutions significantly altered, negatively, all the evaluated properties. But the addition of glutaraldehyde and chlorhexidine did not promote any significant alterations in the evaluated properties.
Fraturas em bases de resina acrílica representam um problema nas reabilitações com próteses totais. Várias pesquisas vêm sendo desenvolvidas buscando-se melhorar a resistência das resinas acrílicas, utilizando, para isso, novos métodos de processamento. O objetivo desse trabalho foi avaliar a influência de dois ciclos de polimerização por microondas sobre a resistência à flexão de um tipo de resina acrílica. Para isso, três grupos foram avaliados (A, B e C), utilizando-se para todos eles a resina acrílica termopolimerizável convencional Clássico. Em dois grupos polimerizou-se a resina acrílica em forno de microondas (Continental AW-30) nos seguintes ciclos: Grupo A) 3 minutos a 500W e Grupo B) pré-polimerização com a mufla posicionada verticalmente por 13 minutos a 90W e polimerização final por 90 segundos a 500W com a mufla na horizontal. O Grupo C foi polimerizado em banho de água quente por 9 horas a 74ºC e utilizado como controle nessa pesquisa. Os corpos-de-prova (n= 9 por grupo) foram submetidos ao ensio de flexão de três pontos na máquina para ensaios mecânicos MTS-810. As médias de resistência flexural (MPa) para os grupos A, B e C foram 101,27 (±12,31),90,66 (±7,56) e 85,06 (±17,50), respectivamente. A análise de variância mostrou diferença significativa entre os grupos avaliados, sendo esta evidenciada entre os grupos A e C através do teste de Tuckey (p<0,05). Concluiuse, dessa forma, que a resina acrílica termopolimerizável convencional Clássico pôde ser polimerizada pela energia de microondas, sem prejuízo à propriedade mecânica avaliada.
Neste trabalho foram analisadas as possíveis alterações promovidas pela incorporação de agentes desinfetantes na resistência à compressão, estabilidade dimensional linear e resistência à tração diametral de modelos em gesso. As amostras foram confeccionadas em gesso pedra tipo III e divididas nos seguintes grupos: Grupo 1- controle (espatulado de acordo com as recomendações do fabricante); Grupo 2- adição de 0,5 % de hipoclorito de cálcio; Grupo 3- adição de 1,0 % de hipoclorito de cálcio; Grupo 4- adição de 1,5 % de hipoclorito de cálcio. Baseado nos resultados obtidos pode se observar que a incorporação de hipoclorito de cálcio influenciou negativamente nos valores de resistência a tração diametral do gesso avaliado, aspecto também observado na resistência a compressão com a incorporação de hipoclorito de cálcio 1,5%. A análise da estabilidade dimensional demonstrou que o agente desinfetante promoveu uma diminuição na expansão de presa apresentada pelo gesso. Com isso, concluímos que a incorporação de hipoclorito de cálcio promove uma tendência à diminuição da expansão apresentada durante a presa do gesso, porém esta incorporação acarreta uma diminuição na resistência dos modelos de gesso.
doi: 10.1111/j.1741‐2358.2011.00462.x Antimicrobial activity of disinfectant agents incorporated into type IV dental stone Purpose: This study evaluated the antimicrobial activity of two disinfectant agents, 2% chlorhexidine digluconate solution (CHX) and 98% chlorhexidine hydrochloride powder (HYD), incorporated into type IV dental stone at the time of mixing. Material and methods: Agar diffusion test was used for the following microorganisms: Escherichia coli, Staphylococcus aureus, Bacillus subtilis and Candida albicans. The specimens were grouped in: (1) dental stone mixed with sterile distilled water; (2) paper disc soaked with CHX; (3) dental stone mixed with CHX; and (4) dental stone with incorporation of HYD, in 1% proportion of the dental stone mass and mixed with sterile distilled water. The culture medium was inoculated with microbial suspensions 1 and 24 h after pouring of the dental stone. The antimicrobial activity was evaluated by the average diameter of microbial growth inhibition zones. The data were analysed with a nested anova (p < 0.05) and Tukey test for specific comparisons. Results: The disinfectant agents demonstrated antimicrobial activity against all microorganisms, with the exception of C. albicans, against which the CHX was ineffective in two periods of analysis. Significant differences between disinfectants were found with all microorganisms. Conclusion: The disinfectant agents analysed were effective against most of the microorganisms tested, except C. albicans.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.