Interference fit joints have been widely used in many engineering constructions, in particular in electric motors. It is of particular importance to calculate the load capacity of press-fit joints, especially in the overload ranges of construction to estimate the safety factor. The article presents a FEM numerical simulation of pressing the shaft into the hub, taking into account various types of fits. The results of numerical simulations presented in the article were positively verified with the MTS measuring device, which confirmed the correctness of the numerical model. So far, the load-bearing capacity of press-fit joints has been calculated from Lame’s formulas. The results of the load capacity of the joints obtained by the FEM simulation were compared with the results obtained from Lame’s formula. The comparison shows that when designing interference fit joints, attention should be paid to the fact that the press-in process, depending on the type of fit, may be elastic-plastic. Plastic deformations in the contact zone of the joint affect its load-bearing capacity. Therefore, the design of press-fit joints should not be based on Lame’s formulas, which do not take into account the range of plastic work of the material.
Na podstawie badań wytrzymałościowych próbek o porowatej strukturze, wydrukowanych w technologii FDM (fused deposition modeling) z filamentów PC/ABS, przeprowadzono symulację numeryczną belek sprężyście zginanych dla 2 różnych gęstości wypełnienia. Wyniki analiz numerycznych zostały zweryfikowane doświadczalnie i porównane z wynikami, jakie uzyskuje się w przypadku przyjęcia handlowych parametrów wytrzymałościowych surowca użytego do druku. Przeprowadzone i planowane badania pozwolą na opracowanie metodyki obliczania konstrukcji o strukturze porowatej, wytworzonych w technologii druku 3D. SŁOWA KLUCZOWE: druk 3D, badania wytrzymałościowe, modelowanie numeryczne Based on the strength tests of porous structure samples printed in FDM technology (fused deposition modeling) from PC/ABS filaments, numerical simulations of bending spring beams for two different filling densities, have been performed. The results of numerical analyzes have been verified experimentally and compared with those obtained with the commercial strength parameters of the raw material used for printing. Conducted and planned studies will allow to develop a methodology for calculating the porous structure created in 3D printing technology. KEYWORDS: 3D printing, strength tests numerical methodsStosowane do niedawna tradycyjne technologie wytwarzania elementów z tworzyw sztucznych i metali zostały uzupełnione o technologię druku 3D, która sprawdza się zwłaszcza w przypadku wytwarzania produktów nieseryjnych lub prototypowych. Możliwości współczesnych drukarek 3D w zakresie tworzenia dowolnych struktur i kształtów z zastosowaniem różnych materiałów wyjścio-wych są imponujące i rozwojowe, a produkty uzyskane tą drogą są przedmiotem wielu badań i analiz [1][2][3][4].Jedną z najpowszechniej stosowanych technologii drukowania obiektów z tworzyw sztucznych jest metoda FDM (fused deposition modeling), polegająca na nanoszeniu przez głowicę drukarki kolejnych warstw roztopionego drutu, wykonanego z tworzywa o znanych właściwościach handlowych. W ten sposób otrzymuje się element o żąda-nym kształcie i wymaganej strukturze wewnętrznej.Technologia druku 3D pozwala na wytwarzanie elementów o porowatej strukturze, co ogranicza ilość zuży-wanego materiału wyjściowego, jednak właściwości mechaniczne finalnego produktu odbiegają od właściwości takich samych produktów o strukturze jednolitej.W przypadku wykonywania symulacji pracy konstrukcji o strukturze porowatej w różnych stanach obciążenia zasadne jest przyjmowanie do obliczeń stałych materiało-wych różniących się od tych, jakie ma materiał, z którego wydrukowano konstrukcję. Przedmiot badań W niniejszym artykule omówiono:• model obliczeniowy belek drukowanych, które poddano sprężystemu zginaniu; • weryfikację doświadczalną wyników otrzymanych na drodze symulacji numerycznej; • porównanie wyników symulacji z wynikami obliczeń, w których przyjęto stałe materiałowe filamentu użytego do druku.Przedmiotem badań są belki drukowane o 2 różnych zagęszczeniach - LOW (niskim) i MED (średnim), wykonane z filamentów PC/A...
Zastosowanie współczesnych technik pomiarowych i obliczeniowych otwiera nowe możliwości w zakresie obliczania i badania konstrukcji metalowych. Zaprezentowano badania prowadzone za pomocą zestawu pomiarowego MTS w celu weryfikacji modelu obliczeniowego konstrukcji zabezpieczenia dachowego, zapewnianiającego bezpieczeństwo konserwatorów pracujących na dachach hal przemysłowych. SŁOWA KLUCZOWE: metody numeryczne, badania wytrzymałościoweThe use of modern measurement techniques and computing methods opens up new possibilities for the calculation and testing of metal structures. This article presents research conducted using measuring set MTS to verify the computational model of the structure of the roof protection on industrial buildings.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.