In this study, a nickel-based superalloy, Waspaloy, was laser heat treated with diode laser. Single laser tracks were manufactured with different laser beam power densities between 63 and 331 kW/cm 2 , and scanning laser beam speed ranged from 5 to 100 m/min. It was found that laser heat treatment of Waspaloy causes decrease in material hardness-the microhardness in laser tracks is about 300 HV0,1 while the microhardness of substrate is ranged from 300 to 600 HV0,1-which is a positive phenomenon for laserassisted machining of investigated material. Impacts of laser heat treatment parameters on laser tracks properties were identified for obtaining multiple laser tracks with the most homogenous thickness. Moreover, roughness of heated layers was measured to specify surface quality after laser heat treatment. Multiple laser tracks were produced using different scanning laser beam speed and distances between laser tracks ranged from 0.125 to 1 mm. It was found that if scanning laser beam speed is 75 m/min and distance between laser tracks is equal to or lower than 0.25 mm, in microstructures of multiple laser tracks, cracks are occurring. The most suitable laser heat parameters for obtaining heated layers, and which can be used for laser-assisted machining, were identified as laser beam power density 178.3 kW/cm 2 , scanning laser beam speed 5 m/min, and distance between laser tracks 0.125 mm.
This study concentrates on describing effects of laser heat treatment of Monel 400 and laser alloying its surface with boron. Surfaces without and with initial boron layers of two different thicknesses (100 and 200 μm) were processed using diode laser. Laser beam power density was constant and equal to 178.3 kW/cm 2 . To determine the influence of laser beam scanning velocity on final properties of treated surfaces, laser beam scanning velocity was set on four different values: 5, 25, 50, and 75 m/min. Microstructures of pure Monel 400 and Monel 400 alloyed with 100 μm boron content are composed of dendrites. Areas laser alloyed with 200 μm boron layer contain mainly nickel borides. Boron addition in Monel 400 surface results in microhardness increase in which the level depends on boron content and the laser beam scanning velocity. Increasing the thickness of initial boron layer and speeding up the laser beam lead to obtain higher microhardness. On the other hand, areas laser alloyed with 200 μm boron layer using laser beam scanning velocity equal to 75 m/min contain deep cracks which propagate from the surface through the produced layer. Furthermore, it was found that the depths of laser heat-treated areas depend significantly on the boron content. As the result of differences in thermal properties between Monel 400 and boron, depth of re-melted zones in some conditions does not lower with increasing laser beam scanning velocity.
In this research, Monel metal was laser heat-treated for microstructural, microhardness and roughness investigation. The treatment is an initial stage for welding Monel without additional material for structural elements. The treatment was carried out with diode laser TruDiode 3006 which allows to reach a power of 3 kW. The material was treated with a constant laser beam power, equal to 1400 W, and four different laser beam velocities: 5, 25, 50 and 75 m/min. The distance between single laser tracks was 0,5 mm in every experimental series. It was found that laser heat treatment of Monel does not influence its hardness. The depth of melted areas is decreasing with an increasing laser beam velocity. The melted area manufactured with laser beam velocity equal to 5 m/min is about 350 μm. Increasing the laser beam velocity to 75 m/min causes depth reduction to about 100 μm. The melted areas are built with column crystals oriented in the direction of heat dissipation perpendicular to the heating direction.
In this study, Monel 400 is laser heat treated and laser alloyed with boron using diode laser to obtain adequate remelting and to improve the microhardness Single laser tracks were produced on the surface with three different laser beam scanning velocities: 5, 25, and 75 m/min. In order to enrich Monel 400 with boron surfaces were covered with initial layers of two different thicknesses before the process: 100 μm and 200 μm. In all experiments, laser beam power density was equal to 178 kW/cm2. Produced laser tracks were investigated in areas of microstructure, depth of remelting and microhardness. It was found that remelted zones are mainly composed of dendrites and the more boron is present in the laser track, the dendritic structure more fragmented is. Depth of remelting and microhardness depend not only on the laser beam scanning velocity but also on thickness of the initial boron layer. While microhardness of Monel 400 is equal to approximately 160 HV0.1, microhardness up to 980 HV0.1 was obtained in areas laser alloyed with boron.
In this study a stainless austenitic steel 1.4550 was laser heat treated with diode laser. The influence a gouache coating on remelted steel substrate was carry out. The cooling system during laser melted was analysis as well. Melted layers were manufactured with different laser beam power between 0.6 kW and 1.4 kW, constant scanning laser beam speed vl = 5.76 m/min and laser beam diameter equal dl = 1.2 mm. The surface was treated at room temperature and under CO2 cooling conditions and the results were compered. With the increase of the laser beam power, the dimensions of the laser tracks increase. The depth of laser tracks varies significantly than their width. The deepest melted layer was observed for a material that wasn’t coated by any of absorbent paste and when there wasn’t cooling system.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.