Insects are among the most agile natural flyers. Hypotheses on their flight control cannot always be validated by experiments with animals or tethered robots. To this end, we developed a programmable and agile autonomous free-flying robot controlled through bio-inspired motion changes of its flapping wings. Despite being 55 times the size of a fruit fly, the robot can accurately mimic the rapid escape maneuvers of flies, including a correcting yaw rotation toward the escape heading. Because the robot's yaw control was turned off, we showed that these yaw rotations result from passive, translation-induced aerodynamic coupling between the yaw torque and the roll and pitch torques produced throughout the maneuver. The robot enables new methods for studying animal flight, and its flight characteristics allow for real-world flight missions.

This paper describes the results of a six-year project aiming at designing and constructing a flapping twin-wing robot of the size of hummingbird (Colibri in French) capable of hovering. Our prototype has a total mass of 22 g, a wing span of 21 cm and a flapping frequency of 22 Hz; it is actively stabilized in pitch and roll by changing the wing camber with a mechanism known as wing twist modulation. The proposed design of wing twist modulation effectively alters the mean lift vector with respect to the center of gravity by reorganization of the airflow. This mechanism is modulated by an onboard control board which calculates the corrective feedback control signals through a closed-loop PD controller in order to stabilize the robot. Currently, there is no control on the yaw axis which is passively stable, and the vertical position is controlled manually by tuning the flapping frequency. The paper describes the recent evolution of the various subsystems: the wings, the flapping mechanism, the generation of control torques, the avionics and the PD control. The robot has demonstrated successful hovering flights with an on-board battery for the flight autonomy of 15-20 s.

Flapping wing micro air vehicles (MAVs) take inspiration from natural fliers, such as insects and hummingbirds. Existing designs manage to mimic the wing motion of natural fliers to a certain extent; nevertheless, differences will always exist due to completely different building blocks of biological and man-made systems. The same holds true for the design of the wings themselves, as biological and engineering materials differ significantly. This paper presents results of experimental optimization of wing shape of a flexible wing for a hummingbird-sized flapping wing MAV. During the experiments we varied the wing 'slackness' (defined by a camber angle), the wing shape (determined by the aspect and taper ratios) and the surface area. Apart from the generated lift, we also evaluated the overall power efficiency of the flapping wing MAV achieved with the various wing design. The results indicate that especially the camber angle and aspect ratio have a critical impact on the force production and efficiency. The best performance was obtained with a wing of trapezoidal shape with a straight leading edge and an aspect ratio of 9.3, both parameters being very similar to a typical hummingbird wing. Finally, the wing performance was demonstrated by a lift-off of a 17.2 g flapping wing robot.

Hovering flapping flight is inherently unstable and needs to be stabilized actively. We present a control mechanism that modulates independently the wing flapping amplitude and offset by displacing joints of a flapping linkage mechanism. We demonstrate its performance by high speed camera recordings of the wing motion as well as by direct measurements of pitch moment and lift force. While flapping at 17 Hz the prototype produces 90 mN of lift and generates pitch moments from-0.7 N.mm to 1.1 N.mm. The mechanism shows low level of cross-coupling in combined pitch and roll commands.

Recently, several insect-and hummingbird-inspired tailless flapping wing robots have been introduced. However, their flight dynamics, which are likely to be similar to that of their biological counterparts, remain yet to be fully understood. We propose a minimal dynamic model that is not only validated with experimental data, but also able to predict the consequences of various important design changes. Specifically, the model captures the flapping-cycle-averaged longitudinal dynamics, considering the main aerodynamic effects. We validated the model with flight data captured with a tailless flapping wing robot, the DelFly Nimble, for air speeds from nearhover flight up to 3.5 m/s. Moreover, the model succeeds in predicting the effects of changes to the center of mass location, and to the control system gains. Hence, the model is suitable even for the initial control design phase. To demonstrate this, we have used the simulation model to tune the robot's control system for higher speeds. Using the new control parameters on the real robot improved its maximal stable speed from 4 m/s to 7 m/s.

The interest in flapping wing MAVs has been rising progressively in the past years. The complex aerodynamic mechanisms responsible for high manoeuvrability and energy efficient lift production have been modelled by multiple techniques. Here we present a comparison of several models from the perspective of flight stability in hover. We estimated the stability derivatives by aerodynamic models of various levels of complexity, ranging from analytical expressions derived from a quasi steady model to CFD results that were taken as a reference. The stability of the complete 6DOF linearized system, split into longitudinal and lateral part, was evaluated in terms of eigenvalues and eigenvectors. While the pole locations and modes of longitudinal system were consistent for all the models (two stable subsidence modes, one unstable oscillatory mode), the lateral dynamics showed that quasi steady models with only translational force are insufficient and revealed the necessity of including the rotational lift to obtain pole locations that are in accordance with the CFD study (one slow divergence mode, one fast subsidence mode and one stable oscillatory mode).

Abstract-Despite an intensive research on flapping flight and flapping wing MAVs in recent years, there are still no accurate models of flapping flight dynamics. This is partly due to lack of free flight data, in particular during manoeuvres. In this work, we present, for the first time, a comparison of free flight forces estimated using solely an on-board IMU with wind tunnel measurements. The IMU based estimation brings higher sampling rates and even lower variation among individual wingbeats, compared to what has been achieved with an external motion tracking system in the past. A good match was found in comparison to wind tunnel measurements; the slight differences observed are attributed to clamping effects. Further insight was gained from the on-board rpm sensor, which showed motor speed variation of ± 15% due to load variation over a wingbeat cycle. The IMU based force estimation represents an attractive solution for future studies of flapping wing MAVs as, unlike wind tunnel measurements, it allows force estimation at high temporal resolutions also during manoeuvres.

No abstract