A blade row which is located downstream of a combustor has an extremely high turbulence intensity at inlet, typically above 10%. The peak turbulent length scale is also high, at around 20% of the chord of the downstream blade row. In a combustor, the turbulence is created by impinging jets in cross flow. This may result in the turbulence being anisotropic in nature. The aim of this paper is to investigate the effect of combustor turbulence on the loss mechanisms which occur in a turbine blade row. The paper has a number of important findings. The combustor turbulence is characterized and is shown to be isotropic in nature. It shows that, when no pressure gradient is present, combustor turbulence increases the loss of a turbulent boundary layer by 22%. The mechanism responsible for this change is shown to be a deep penetration of the turbulence into the boundary layer. It shows that the presence of combustor turbulence increases the profile loss and endwall loss in the turbine cascade studied by 37% and 47%, respectively. The presence of combustor turbulence also introduces a freestream loss resulting in the total loss of the turbine cascade rising by 47%. When these loss mechanisms were applied to the vane alone, of an engine representative high pressure turbine, it was found to result in a 1.3% reduction in stage efficiency.

A blade row which is located downstream of a combustor has an extremely high turbulence intensity at inlet, typically above 10%. The peak turbulent length scale is also high, at around 20% of the chord of the downstream blade row. In a combustor, the turbulence is created by impinging jets in cross flow. This may result in the turbulence being anisotropic in nature. The aim of this paper is to investigate the effect of combustor turbulence on the loss mechanisms which occur in a turbine blade row. The paper has a number of important findings. The combustor turbulence is characterized and is shown to be isotropic in nature. It shows that, when no pressure gradient is present, combustor turbulence increases the loss of a turbulent boundary layer by 22%. The mechanism responsible for this change is shown to be a deep penetration of the turbulence into the boundary layer. It shows that the presence of combustor turbulence increases the profile loss and endwall loss in the turbine cascade studied by 37% and 47%, respectively. The presence of combustor turbulence also introduces a freestream loss resulting in the total loss of the turbine cascade rising by 47%. When these loss mechanisms were applied to the vane alone, of an engine representative high pressure turbine, it was found to result in a 1.3% reduction in stage efficiency.

This paper describes a framework to quantify the effect of freestream turbulence, generated by mixing processes in a combustor, on turbulent boundary layer loss generation in the high pressure turbine downstream of the combustor. The regime of freestream turbulence common to gas turbine aero engines is identified and it is shown that the dissipation loss coefficient in this regime can be determined using existing measurements of the effect of freestream turbulence on skin friction. The paper shows that combustor-generated freestream turbulence can increase the profile loss coefficient of a typical high pressure turbine blade by as much as 28%. A relation has been derived between a non-dimensional turbulence parameter, which characterizes the freestream turbulence, and the increase in turbine boundary layer dissipation, which quantifies the decrease in turbine efficiency. The relation provides guidelines for combustor turbulence modifications that lead to turbine performance benefits. The framework has been applied in example trade studies which show that increasing the size of dilution ports and increasing the length of the combustor can decrease high pressure turbine profile loss generation to potentially increase stage efficiency up to 0.5%.

This paper describes a framework to quantify the effect of freestream turbulence, generated by mixing processes in a combustor, on turbulent boundary layer loss generation in the high pressure turbine downstream of the combustor. The regime of freestream turbulence common to gas turbine aero engines is identified and it is shown that the dissipation loss coefficient in this regime can be determined using existing measurements of the effect of freestream turbulence on skin friction. The paper shows that combustor-generated freestream turbulence can increase the profile loss coefficient of a typical high pressure turbine blade by as much as 28%. A relation has been derived between a non-dimensional turbulence parameter, which characterizes the freestream turbulence, and the increase in turbine boundary layer dissipation, which quantifies the decrease in turbine efficiency. The relation provides guidelines for combustor turbulence modifications that lead to turbine performance benefits. The framework has been applied in example trade studies which show that increasing the size of dilution ports and increasing the length of the combustor can decrease high pressure turbine profile loss generation to potentially increase stage efficiency up to 0.5%.