Densely packed exfoliated nanosheet films such as Ti0.91O2, Ti0.8M0.2O2 (M = Co, Ni), Ti0.6Fe0.4O2, and Ca2Nb3O10 on solid substrates were prepared by the LB transfer method without any amphiphilic additives at the air-water interface. Nanosheet crystallites covered nearly 95% on the solid surface with minimum overlapping of nanosheets. The LB transfer method of the Ti0.91O2 nanosheet monolayer film is applicable for not only hydrophilic substrates such as quartz, silicon, indium-tin oxide (ITO), and glass but also the hydrophobic Au surface. On the basis of these points, the LB transfer method has advantages compared to the alternating layer-by-layer method, which makes use of oppositely charged polyelectrolytes such as poly(ethylenimine) (PEI). Adsorption of hydrophobic Ti0.91O2 nanosheets at the air-water interface is responsible for this LB transfer deposition method. The addition of tetrabutylammonium bromide into the subphase assisted the adsorption, causing an increase in the adsorbed amount of Ti0.91O2 nanosheets at the air-water interface.

Self-assembled multilayer films of titania nanoparticles and composite films of nanoparticles/nanosheets have been fabricated on various substrates using appropriate polyelectrolytes as counterions. UV−vis spectroscopy and ellipsometric data for the multilayer buildup process of TiO2 nanoparticles indicated that a nearly equivalent amount of nanoparticles can be deposited layer-by-layer with a polyanion such as poly(sodium 4-styrene sulfonate). The average thickness of the TiO2 nanoparticle layer was determined to be about 6.3 nm, which is in good agreement with TEM and AFM data. TiO2 nanoparticles and Ti1 - δO2 nanosheets are assembled in various sequences with appropriate polyelectrolytes sandwiched between them, which yielded novel intergrown nanoparticle/nanosheet films. Polymers between the nanoparticle and/or nanosheet layers could be decomposed by UV irradiation to yield inorganic multilayer films, which is confirmed by IR and X-ray photoelectron spectroscopy combined with Ar+ depth profiling. Small ions such as SO4 2- and NH4 + were resulted from polymers as counterions for the nanoparticles and nanosheets.

Alternating multilayer films composed of titania nanosheets and Zn porphyrins were prepared by use of a previously reported Langmuir-Blodgett film-transfer method in order to fabricate photoelectrochemical devices. Closely packed titania nanosheet monolayers on indium tin oxide (ITO), mica, and quartz surfaces strongly adsorbed cationic [5,10,15,20-tetrakis(1-methylpyridinium-4-yl)porphyrinatozinc]4+ (ZnTMPyP4+) by electrostatic interactions. The alternating deposition process afforded nanometer-scale multilayer films with the following structure: solid surface/(titania nanosheet/ZnTMPyP4+)n (n is the number of layers). The multilayer films were characterized by various physical measurements, including AFM, XRD, and UV-visible spectra. The visible-light irradiation of this multilayer film on an ITO electrode in the presence of triethanolamine as an electron donor yielded an anodic photocurrent. The action spectrum was consistent with the absorption spectrum of ZnTMPyP4+, which indicates that the photoexcitation of ZnTMPyP4+ is responsible for the photocurrent generation. However, the photocurrent density decreased with an increasing number of layers, which indicates that the harvesting of photoexcited electrons vertically through the titania nanosheets in the ITO/(titania nanosheet/ZnTMPyP4+)n structure was not efficient. To overcome this problem, the use of a lateral interlayer connection to all of the titania nanosheets with Ag paste was examined. As a result, a dramatic improvement in the photocurrent density was obtained. Thus, for efficient photocurrent generation with the titania nanosheet-ZnTMPyP4+ composite material, the lateral connection to all of the titania nanosheet layers is effective.