We present a technique to initiate chemical reactions involving few reactants inside micrometer-scale biomimetic vesicles (10(-12) to 10(-15) L) integral to three-dimensional surfactant networks. The shape of these networks is under dynamic control, allowing for transfer and mixing of two or several reactants at will. Specifically, two nanotube-connected vesicles were filled with reactants (substrate and enzyme, respectively) by microinjection. Initially, the vesicles are far apart and any diffusive mixing (on relevant experimental time scales) between the contents of the separated vesicles is hindered because of the narrow diameter and long axial extension of the nanotube. To initiate a reaction, the vesicles were brought close together, the nanotube was consumed by the vesicles and at a critical distance, the nanotube-vesicle junctions were dilated leading to formation of one spherical reactor, and hence mixing of the contents. We demonstrate the concept using a model enzymatic reaction, which yields a fluorescent product (two-step hydrolysis of fluorescein diphosphate by alkaline phosphatase), where product formation was measured as a function of time using a FRAP fluorescence microscopy protocol. By comparing the enzymatic activity with bulk measurements, the enzyme concentration inside the vesicle could be determined. Reactions could be followed for systems having as few as approximately 15 enzyme molecules confined to a reactor vesicle. To describe the experiments we use a simple diffusion-controlled reaction model and solve it using a survival probability approach. The agreement with experiment is qualitative, but the model describes the trends well. It is shown that the model correctly predicts (i) single-exponential decay after a few seconds, and (ii) that the substrate decay constant depends on the number of enzymes and geometry of reaction container. The numerical correction factor Lambda is introduced in order to ensure semiquantitative agreement between experiment and theory. It was shown that this numerical factor depends weakly on vesicle radius and number of enzymes, thus it is sufficient to determine this factor only once in a single calibration measurement.

In this work, we present preparation and basic applications of lipid-bilayer-enclosed picoliter volumes (microcontainers) of solutions of poly(N-isopropylacrylamide) (PNIPAAm). Giant unilamellar vesicles (GUVs) were prepared from phospholipids using a standard swelling procedure and subsequently surface immobilized. Clear, slightly viscous solutions of PNIPAAm of varying concentration in aqueous buffer were directly pressure-microinjected into the GUVs, using a submicrometer-sized, pointed capillary. The GUV was subjected to changing temperature over a 21-40 degrees C range. The typical phase transition of the polymeric material upon heating and cooling across the lower critical solution temperature was followed using optical microscopy and shown to be reversible over multiple sequential heating/cooling cycles without compromising the integrity of the GUV membrane. Fluorescent, carboxylic acid modified 200 nm latex beads, co-injected with the PNIPAAm solution, were temperature-reversibly immobilized during the phase transition, practically freezing the Brownian motion of the entrapped particles in the volume. Furthermore, a co-injected water soluble fluorescent polysaccharide-dye conjugate was shown not to migrate from the aqueous phase into the hydrophobic polymer part upon heating, whereas the fluorescent beads were completely but reversibly immobilized in the hydrophobic domains of dense polymer agglomerates. The system reported here provides a feasible method for the reversible stabilization and solidification of GUV interior volumes, e.g., as a micrometer-sized model system for controlled drug release.

Giant unilamellar vesicles (GUVs) were microinjected with aqueous solutions of poly(N-isopropyl acrylamide) (PNIPAAm). Temperature-dependent sol-gel phase transitions of the solutions, followed by shrinking and swelling of the resulting hydrogel, were studied in the presence of a variety of co-solutes within the GUV. Reversible formation of a dense, spherical hydrogel structure (compartment) was observed in all cases with defined shrinking/swelling behaviour at temperatures above the lower critical solution temperatures (LCSTs). Nanotube-mediated merging of two vesicles with thus formed compartments resulted in a single GUV with two internalized hydrogel structures. As an application example, we demonstrate how fluorescent nanoparticles can be immobilized in such gel structures.

The introduction of poly(ethylene dioxythiophene) (PEDOT)/poly(styrene sulfonate) (PSS) polyelectrolyte into giant unilamellar phospholipid vesicles (GUVs) and cross-linking with Ca2+ ions to generate a hydrogel within the internal compartment are reported. The aqueous colloidal suspension of PEDOT with excess PSS was microinjected into the internal compartment of liposomes as well as networks of GUVs and lipid nanotubes. The subsequent introduction of calcium ions as cross-linking agent in order to induce hydrogel formation was achieved by three different methods: vesicle fusion, electroporation, and direct microinjection. Gel formation was probed by coinjection of fluorescent nanoparticles and tracking of Brownian motion. Particle mobility was shown to be distinctly reduced in the gel-filled vesicles. Diffusion constants for the particles were calculated from the projected movement of the particles and compared to particles in reference gels and solutions.

This work addresses novel means for controlled mixing and reaction initiation in biomimetic confined compartments having volume elements in the range of 10(-12) to 10(-15) L. The method is based on mixing fluids using a two-site injection scheme into growing surfactant vesicles. A solid-state injection needle is inserted into a micrometer-sized vesicle (radius 5-25 microm), and by pulling on the needle, we create a nanoscale surfactant channel connecting injection needle and the vesicle. Injection of a solvent A from the needle into the nanotube results in the formation of a growing daughter vesicle at the tip of the needle in which mixing takes place. The growth of the daughter vesicle requires a flow of surfactants in the nanotube that generates a flow of solvent B inside the nanotube which is counterdirectional to the pressure-injected solvent. The volume ratio psi between solvent A and B inside the mixing vesicle was analyzed and found to depend only on geometrical quantities. The majority of fluid injected to the growing daughter vesicle comes from the pressure-based injection, and for a micrometer-sized vesicle it dominates. For the formation of one daughter vesicle (conjugated with a 100-nm radius tube) expanded from 1 to 200 microm in radius, the mixing ratios cover almost 3 orders of magnitude. We show that the system can be expanded to linear strings of nanotube-conjugated vesicles that display exponential dilution. Mixing ratios spanning 6 orders of magnitude were obtained in strings of three nanotube-conjugated micrometer-sized daughter vesicles.