Even after a decade or so of research, the direct synthesis of highly crystalline mesoporous transition-metal oxides that are thermally stable and well ordered still constitutes a major challenge. Although various soft- and hard-templating approaches have been developed in the past, they usually suffer from multiple, tedious steps and often result in poor structure control. For many applications including power generation and energy conversion, however, high crystallinity and controlled mesoporosity are a prerequisite. To this end, here we report on an approach established for group-IV (titanium) and group-V (niobium) oxides, with potential applications to photovoltaic cells and fuel cells, respectively, which overcomes previous limitations. It gives direct access to the desired materials in a 'one-pot' synthesis using block copolymers with an sp2-hybridized carbon-containing hydrophobic block as structure-directing agents which converts to a sturdy, amorphous carbon material under appropriate heating conditions. This in situ carbon is sufficient to act as a rigid support keeping the pores of the oxides intact while crystallizing at temperatures as high as 1,000 degrees C.

Catechols play an important role in many natural systems. They are known to readily interact with both organic (e.g., amino acids) and inorganic (e.g., metal ions, metal oxides) compounds, thereby providing a powerful system for protein curing. Catechol crosslinked protein networks, such as sclerotized cuticle and byssal threads of the mussel, have been shown to exhibit excellent mechanical properties. A lot of effort has been devoted to mimicking the natural proteins using synthetic catechol-functionalized polymers. Despite the success in developing catechol-functionalized materials, the crosslinking chemistry of catechols is still a subject of debate. To develop materials with controlled and superior properties, a clear understanding of the crosslinking mechanism of catechols is of vital importance. This review describes the crosslinking pathways of catechol and derivatives in both natural and synthetic systems. We discuss existing pathways of catechol crosslinking and parameters that affect the catechol chemistry in detail. This overview will point towards a rational direction for further investigation of the complicated catechol chemistry.

The synthesis of ordered mesoporous metal composites and ordered mesoporous metals is a challenge because metals have high surface energies that favor low surface areas. We present results from the self-assembly of block copolymers with ligand-stabilized platinum nanoparticles, leading to lamellar CCM-Pt-4 and inverse hexagonal (CCM-Pt-6) hybrid mesostructures with high nanoparticle loadings. Pyrolysis of the CCM-Pt-6 hybrid produces an ordered mesoporous platinum-carbon nanocomposite with open and large pores (>/=10 nanometers). Removal of the carbon leads to ordered porous platinum mesostructures. The platinum-carbon nanocomposite has very high electrical conductivity (400 siemens per centimeter) for an ordered mesoporous material fabricated from block copolymer self-assembly.

We report the first successful application of an ordered bicontinuous gyroid semiconducting network in a hybrid bulk heterojunction solar cell. The freestanding gyroid network is fabricated by electrochemical deposition into the 10 nm wide voided channels of a self-assembled, selectively degradable block copolymer film. The highly ordered pore structure is ideal for uniform infiltration of an organic hole transporting material, and solid-state dye-sensitized solar cells only 400 nm thick exhibit up to 1.7% power conversion efficiency. This patterning technique can be readily extended to other promising heterojunction systems and is a major step toward realizing the full potential of self-assembly in the next generation of device technologies.

several excellent reviews. [9][10][11][12] Recently, it was emphasized by Waite that catechol moieties alone are insufficient to ensure proper underwater adhesion and that the performance is a complex interplay between DOPA and its local environment. [13] Therefore, attention is shifted to include other (noncovalent) interactions used in these natural glues, and much progress has been made in understanding both their performance and delivery process. [14] In this review, we take the sandcastle worm and mussel as a basis for inspiration. We discuss (noncovalent) interactions found in these natural adhesive systems and extend our discussion to additional supramolecular moieties that can be used to control the adhesive and cohesive performance of synthetically designed adhesives. In Section 2, we examine the natural systems and identify the versatile supramolecular interactions used in such protein-based adhesives. These include electrostatic interactions, hydrogen bonding, hydrophobic forces, π-π interactions, metal coordination, cation-π complexation, and dynamic covalent linkages. The use of these interactions in synthetic adhesive systems is explored in the subsequent sections. Section 3 is devoted to the different interactions that catechols (the functional group of DOPA) display to bond to a submerged substrate or to provide cohesive properties to the adhesive. Despite the fact that catechols have already been the topic of many excellent reviews, [9,13,17] we believe that catechols play a pivotal role in both the sandcastle worm and the mussel adhesive systems and, therefore, should not be omitted from this review. In Section 4, we discuss the use of electrostatic interactions in protein-based and synthetic adhesive formulations for wet conditions. These interactions can be tailored to a wide distribution of bond strengths and thus can be tuned to change multi ple mechanical properties, which is essential for design of an adhesive. Besides the effect on the adhesive and cohesive properties, we highlight work where electrostatic interactions cause liquid-liquid phase separation in aqueous polymer solutions. The resulting (complex) coacervate is a concentrated, liquid, yet water-insoluble phase of the adhesive material, which can act as a powerful delivery tool for underwater adhesives. Hydrogen bonding in adhesives is explored in Section 5. The use of hydrogen bonding to adjust the viscoelastic properties of adhesives has been identified decades, ago, and hydrogen bonding moieties are commonly used in pressure sensitive adhesives (PSAs). However, besides simple, single hydrogen bonding motifs, many interesting alternative Nature has developed protein-based adhesives whose underwater performance has attracted much research attention over the last few decades. The adhesive proteins are rich in catechols combined with amphiphilic and ionic features. This combination of features constitutes a supramolecular toolbox, to provide stimuli-responsive processing of the adhesive, to secure strong adhesion to a variety of...

While nature has optimized its antifouling strategies over millions of years, synthetic antifouling coatings have not yet reached technological maturity. For an antifouling coating to become technically feasible, it should fulfill many requirements: high effectiveness, long‐term stability, durability, ecofriendliness, large‐scale applicability, and more. It is therefore not surprising that the search for the perfect antifouling coating has been going on for decades. With the discovery of metal‐based antifouling paints in the 1970s, fouling was thought to be a problem of the past, yet its untargeted toxicity led to serious ecological concern, and its use became prohibited. As a response, research shifted focus toward a biocompatible alternative: polymer‐based antifouling coatings. This has resulted in numerous advanced and innovative antifouling strategies, including fouling‐resistant, fouling‐release, and fouling‐degrading coatings. Here, these novel and exciting discoveries are highlighted while simultaneously assessing their antifouling performance and practical feasibility.

Nature has developed reversibly adhesive surfaces whose stickiness has attracted much research attention over the last decade. The central lesson from nature is that “patterned” or “fibrillar” surfaces can produce higher adhesion forces to flat and rough substrates than smooth surfaces. This paper critically examines the principles behind fibrillar adhesion from a contact mechanics perspective, where much progress has been made in recent years. The benefits derived from “contact splitting” into fibrils are separated into extrinsic/intrinsic contributions from fibril deformation, adaptability to rough surfaces, size effects due to surface‐to‐volume ratio, uniformity of stress distribution, and defect‐controlled adhesion. Another section covers essential considerations for reliable and reproducible adhesion testing, where better standardization is still required. It is argued that, in view of the large number of parameters, a thorough understanding of adhesion effects is required to enable the fabrication of reliable adhesive surfaces based on biological examples.

Sandcastle worms have developed protein‐based adhesives, which they use to construct protective tubes from sand grains and shell bits. A key element in the adhesive delivery is the formation of a fluidic complex coacervate phase. After delivery, the adhesive transforms into a solid upon an external trigger. In this work, a fully synthetic in situ setting adhesive based on complex coacervation is reported by mimicking the main features of the sandcastle worm's glue. The adhesive consists of oppositely charged polyelectrolytes grafted with thermoresponsive poly(N‐isopropylacrylamide) (PNIPAM) chains and starts out as a fluid complex coacervate that can be injected at room temperature. Upon increasing the temperature above the lower critical solution temperature of PNIPAM, the complex coacervate transitions into a nonflowing hydrogel while preserving its volume—the water content in the material stays constant. The adhesive functions in the presence of water and bonds to different surfaces regardless of their charge. This type of adhesive avoids many of the problems of current underwater adhesives and may be useful to bond biological tissues.