Miháliková M., Matula S., Doležal F. (2013) The database of soil hydrophysical properties in the Czech Republic called HYPRESCZ was created. It is based on the European database HYPRES, HYdraulic PRoperties of European Soils, and follows its structure with few modifications. It collects the available data from the Czech Republic from which pedotransfer functions (PTFs) for the estimation of soil hydrophysical properties from easily available soil properties can be derived and 2101 database entries were collected. The entries have different quality of data, out of the total number of entries 707 entries were applicable to PTFs derivation for the estimation of soil water retention curves (SWRCs). After elimination of replicates, finally 159 unique soil horizons (arable land only) were used for PTFs derivation. The parametric continuous pedotransfer functions for estimation of SWRCs in the Czech Republic were derived within this study and are based on Wösten's model. The retention curves were estimated using both these newly derived PTFs and Wösten's original model, which was derived for European soils in general. The uncertainty of estimation was evaluated, employing the root mean squared error (RMSE) and the coefficient of determination (R 2 ) comparing the PTF-estimated and the directly fitted retention curves. The reliability of the newly derived PTFs for Czech soils was higher (RMSE = 0.059 cm 3 /cm 3 and R 2 = 71%) compared to Wösten's general PTFs (RMSE = 0.11 cm 3 /cm 3 and R 2 = 36%).

The unsaturated hydraulic conductivity K(h) is a key soil parameter governing the water and solute transportation processes. The course of this function depends on the geometry of the pores which is determined by the soil's physical and chemical properties. Many studies focus on the comparison of soil hydraulic conductivity under different conditions. Despite the recent progress in this research field, no reference method for measuring the K(h) in situ exists. This study focuses on the effect of the initial water content of the soil as a factor influencing the measured K(h). The study was performed in situ over short time period and with several replications close to each other in order to reduce the effect of other factors which could cause variations. Two tension infiltrometers were used and compared: A Hood infiltrometer IL-2700 and a Minidisk infiltrometer. Three different levels of initial water content (dry, medium wet and wet) were applied for each of the two infiltrometers, and three pressure heads (-0.5; -1 and -3 cm) for each measurement. According to the results, the Minidisk infiltrometer showed significant sensitivity to the initial water content, while measurements performed using the Hood infiltrometer were more stable.

Hydraulic conductivity at and near saturation (Ks and K(h)) are among the most important characteristics defining water behavior in soil. Characterization of possibilities, advantages and limitations of the Mini Disk infiltrometer (MDI) for Ks and K(h) determination in comparison with Hood infiltrometer (HI) was the main aim of this study. The MDI device was subjected to testing on a cultivated silty clay loam soil under three different tillage treatments; conventional, reduced and no-tillage plot. The results are based on 72 infiltration experiments carried out during four experimental phases within one year. Steady-state and transient data analysis methods were applied. K(h) values were determined for van Genuchten hydraulic parameters taken from different sources (two versions of User’s manual, Rosetta). The results show suitability of MDI to determine K(h) of tested soil; clear differences have been observed between the K(h) values measured on plots with different tillage treatment. However, these values were significantly lower (ANOVA, α = 0.05) than those measured by HI. MDI based data were reflecting seasonal changes in structure and pore-size distribution with quantification of macropore contribution to the total saturated flux. Application of K(h) MDI data for fine-textured and structural soils evaluated before 2010 should be reconsidered.

Improvement of agricultural water management by implementing more efficient irrigation methods is essential for sustainable use of water and soil resources. The main objective was to assess and compare the use of parametric evaluation (PM) and multi‐criteria assessment (MCA) in the decision and planning process of irrigation management by land suitability assessment of three irrigation techniques. Land and soil properties were determined and assessed, and suitability maps were produced for surface, sprinkler and drip irrigation methods in the Çarşamba Delta plain (Black Sea region, Turkey; 972.2 ha). MCA was more flexible and sensitive due to the analytical hierarchy process and thus better reflected real conditions, than the widely used PM. In both approaches, drip irrigation was the most suitable. The main restricting factors in all irrigation systems in this area were slope, soil depth and soil texture. Results demonstrated that the arability of 33% (PM) or 30% (MCA) of the study area would be improved by employing drip irrigation instead of surface or sprinkler irrigation. Maps show where the change of traditional surface irrigation system should start. Such a change would be projected into better water use efficiency and more efficient use of soil while reducing degradation processes, namely soil erosion. © 2019 John Wiley & Sons, Ltd.

Lysimeters are basic instruments for evapotranspiration measurement. This study characterized the actual evapotranspiration of unirrigated and unfertilized grass in a warm region of the Czech Republic on a Chernozem loamy soil. An SFL-300 weighing lysimeter (diameter 0.3 m, depth 0.3 m) was used for this purpose. The suction at its bottom was maintained at the same level as in the native soil nearby. We selected 585 rainless days with regular records for the analysis of daily differences. On most days, the lysimeter-measured actual evapotranspiration, ET a , was smaller than the Penman-Monteith FAO 56 reference crop evapotranspiration, ET 0 . The FAO 56 procedure was found to be a reasonable estimator of the unstressed evapotranspiration in a moderately stressed environment. The ET a /ET 0 ratio and the canopy surface resistance, r s , depend on the soil water content and suction measured at 5 cm. These graphs break down into horizontal unstressed parts and declining (for ET a /ET 0 ) or inclining (for r s ) water-stressed parts. The ratio ET a /ET 0 is about 85% and r s is about 250 s m −1 when the grass is not under water stress. The annual curve of the unstressed crop coefficient has a sine shape. An energy balance criterion suggests that advection of heat is important in winter but not so much in summer. The study provides parameters of evapotranspiration for a canopy that can be found on many standard weather stations and demonstrates that high-quality research into evapotranspiration of low, dense, and shallow-rooting crops is possible with small lysimeters of this type.Abbreviations: ASCE, American Society of Civil Engineers; DOY, day of the year; ET, evapotranspiration; ET a , actual evapotranspiration; ET 0 , reference crop evapotranspiration; LYW, lysimeter weight (actually mass); SFL, smart field lysimeter; SWW, percolate collecting bottle mass.Evapotranspiration is a basic component of the natural water cycle and water balance. Its quantification is therefore of utmost importance for many branches of water management. The potential evapotranspiration, representing the climatic "demand" for water (Hillel, 1998;Irmak and Haman, 2003;Verstraeten et al., 2008) has long ago been recognized as a suitable benchmark to which other types of evaporation in nature can be related. The FAO 24 (Doorenbos and Pruitt 1977) and then the FAO 56 (Allen et al., 1998) and American Society of Civil Engineers (ASCE) (Jensen and Allen, 2016) methodologies offered a concept of the reference crop evapotranspiration, ET 0 , corresponding to the actual evapotranspiration of a standard, dense, and extensive herbal stand sufficiently supplied with soil water (and thus its potential evapotranspiration). The FAO 56 reference low crop is grass, assumed to be 0.12 m high, having a shortwave albedo of 0.23 and surface resistance of 70 s m −1 . Up to now, one of the widely used way of estimating ET 0 has been the one based on the Penman combination concept resulting in the PenmanMonteith evaporation equation (cf. Allen et al., 1998; f...

Báťková K., Matula S., Miháliková M., Chala A.T., Moreira Barradas J.M., Mekonnen G.B. (2014): Testing of activated carbon for water and non-volatile LNAPL quantitative determination in porous media under laboratory conditions. Soil & Water Res., 9: 161-168.Activated carbon is a highly porous form of carbon, which has an exceptionally large surface area. Activated carbon material has been artificially processed as a set of plates, within which two different types of pores are present: micropores (< 2 nm) and transport pores (macropores > 50 nm and mesopores 2-50 nm). The transport pores bring molecules of different substances (organic compounds) into the micropores, which are basically the active centres where the adsorption takes place. Activated carbon, due to its high adsorption potential, is used in many applications such as air, water, wastewater or chemical purification. In this study, the pelletized activated carbon (Silcarbon SC40) was tested for water and non-volatile LNAPL (Light Non-Aqueous Phase Liquid; medicinal mineral oil used in this study) determination in a porous medium (silica sand). The experiments were carried out under controlled laboratory conditions. Three different sets of experiments were carried out: (i) the water or LNAPL adsorption from pure media (water or LNAPL liquids); (ii) the water or LNAPL adsorption from pure media (water or LNAPL vapours); (iii) water and/or LNAPL adsorption from the porous material at different sampling intervals. Furthermore, the water/LNAPL contents of the porous media were determined on the basis of the water/LNAPL contents of sampled Silcarbon SC40. The results confirmed the suitability of the Silcarbon SC40 for water/LNAPL sampling from the porous media under laboratory conditions. The method is suitable for detection of water and/or LNAPL in a liquid or gaseous phase and also for water and/or LNAPL quantitative determination. For the quantitative determination a calibration of this method would be required.Keywords: activated carbon; LNAPL; silica sand; Silcarbon SC40; sampling interval Organic contaminants are one of the most common substances contaminating the vadose and saturated zones of soil and rock environments. Light NonAqueous Phase Liquids (LNAPLs) represent a group of organic substances that are relatively insoluble in water and are less dense than water (US EPA 2012). The LNAPLs move through the vadose zone towards the ground water level; its lateral movement can start even before the LNAPL reaches the ground water level due to the capillary fringe and saturated conditions above the ground water level (Cohen & Mercer 1990). Quite a lot of effort has been invested in studies of LNAPL behaviour in homogeneous conditions (Lenhard et al. 1993;Ostendorf et al. 1993;Eckberg & Sunada 1984). However, LNAPL transport within heterogeneous media has not been investigated thoroughly and requires further research (Schroth et al. 1998). In the past, research was aimed at applications in the petroleum industry. Recently however preferences have ...

No abstract

The DSS-FS fertigation simulator is intended to support design and optimization of irrigation and fertigation systems while increasing their environmental sustainability. The DSS-FS is a decision support system aiming to simplify the design of advanced irrigation systems, including fertigation features assuring its optimal efficiency and error minimization. Data from farms where the DSS-FS was used (as the primary consulting system) were analysed and are presented in this article. This system has proven to be user friendly and is reported by the majority of users to increase production by considerable amounts, saving 20-30% in input factors and energy. Now, further aided by user feedback, the system will continue to be optimized, with a view to improving current functionalities and implementing new ones, as well as extending its applicability. Copyright © 2014 John Wiley & Sons, Ltd. RÉSUMÉLe simulateur de fertigation DSS-FS est destiné à soutenir la conception et l'optimisation des systèmes d'irrigation et de fertigation tout en augmentant leur durabilité environnementale. Le DSS-FS est un système d'aide à la décision visant à simplifier la conception des systèmes d'irrigation avancés, qui intègre les caractéristiques de fertigation, assure l'efficacité du système et minimise les erreurs. Les données issues d'une consultation primaire des fermes où le DSS-FS est utilisé ont été analysées, et les résultats sont présentés dans cet article. Le système a fait ses preuves pour être convivial, et la majorité des utilisateurs rapportent que la production augmente en quantités considérables, alors que des facteurs d'entrée et d'énergie sont réduits de 20 à 30%. Maintenant, grâce aux retours des utilisateurs, le système continuera à être optimisé, en vue de l'amélioration des fonctionnalités actuelles et de la mise en oeuvre de nouvelles, ainsi que l'extension de son domaine d'application.