No abstract

SUMMARY Directional arrays of branched microscopic setae constitute a dry adhesive on the toes of pad-bearing geckos, nature's supreme climbers. Geckos are easily and rapidly able to detach their toes as they climb. There are two known mechanisms of detachment: (1) on the microscale, the seta detaches when the shaft reaches a critical angle with the substrate, and (2) on the macroscale, geckos hyperextend their toes, apparently peeling like tape. This raises the question of how geckos prevent detachment while inverted on the ceiling, where body weight should cause toes to peel and setal angles to increase. Geckos use opposing feet and toes while inverted, possibly to maintain shear forces that prevent detachment of setae or peeling of toes. If detachment occurs by macroscale peeling of toes, the peel angle should monotonically decrease with applied force. In contrast, if adhesive force is limited by microscale detachment of setae at a critical angle, the toe detachment angle should be independent of applied force. We tested the hypothesis that adhesion is increased by shear force in isolated setal arrays and live gecko toes. We also tested the corollary hypotheses that (1) adhesion in toes and arrays is limited as on the microscale by a critical angle, or (2)on the macroscale by adhesive strength as predicted for adhesive tapes. We found that adhesion depended directly on shear force, and was independent of detachment angle. Therefore we reject the hypothesis that gecko toes peel like tape. The linear relation between adhesion and shear force is consistent with a critical angle of release in live gecko toes and isolated setal arrays, and also with our prior observations of single setae. We introduced a new model,frictional adhesion, for gecko pad attachment and compared it to existing models of adhesive contacts. In an analysis of clinging stability of a gecko on an inclined plane each adhesive model predicted a different force control strategy. The frictional adhesion model provides an explanation for the very low detachment forces observed in climbing geckos that does not depend on toe peeling.

This paper presents an integrated, systems level view of several novel design and control features associated with the biologically-inspired, hexapedal, RiSE robot. RiSE is the first legged machine capable of locomotion on both the ground and a variety of vertical building surfaces including brick, stucco, and crushed stone at speeds up to 4 cm/s, quietly and without the use of suction, magnets, or adhesives. It achieves these capabilities through a combination of bio-inspired and traditional design methods. This paper describes the design process and specifically addresses body morphology, hierarchical compliance in the legs and feet, and sensing and control systems that enable robust and reliable climbing on difficult surfaces. Experimental results illustrate the effects of various behaviors on climbing performance and demonstrate the robot's ability to climb reliably for long distances.

Gecko adhesion has become a paradigmatic example of bio-inspired engineering, yet among the many gecko-like synthetic adhesives (GSAs), truly gecko-like performance remains elusive. Many GSAs have previously demonstrated one or two features of the gecko adhesive. We present a new wedge-shaped GSA that exhibits several gecko-like properties simultaneously: directional features; zero force at detachment; high ratio of detachment force to preload force; non-adhesive default state; and the ability to maintain performance while sliding, even after thousands of cycles. Individual wedges independently detach and reattach during sliding, resulting in high levels of shear and normal adhesion during drag. This behaviour provides a non-catastrophic failure mechanism that is desirable for applications such as climbing robots where sudden contact failure would result in serious falls. The effects of scaling patch sizes up to tens of square centimetres are also presented and discussed. Patches of 1 cm 2 had an adhesive pressure of 5.1 kPa while simultaneously supporting 17.0 kPa of shear. After 30 000 attachment/detachment cycles, a patch retained 67 per cent of its initial adhesion and 76 per cent of its initial shear without cleaning. Square-based wedges of 20 mm and 50 mm are manufactured in a moulding process where moulds are fabricated using a dual-side, dual-angle lithography process on quartz wafers with SU-8 photoresist as the mould material and polydimethylsiloxane as the cast material.

No abstract

No abstract

The goal of this article is to develop practical descriptions of the relationship between forces and motions in sliding manipulation. We begin by reviewing the limit surface, a concept from the mechanics of sliding bodies that uses kinematic analysis to find the force and moment required to produce any given sliding motion. Next we provide experimental results showing that the limit surface only approximates the actual force-motion relationship. Then we look at other approximations that can be used to provide a simplified model useful in control, planning, and simulation of manipulation. These approximations include square pyramids, cones, ellipsoids, and ellipsoids with facets removed. Different approximations may be most appropriate, depending on the required computational speed and accuracy and the need to produce conservative results.

We describe a MRI-compatible biopsy needle instrumented with optical fiber Bragg gratings for measuring bending deflections of the needle as it is inserted into tissues. During procedures, such as diagnostic biopsies and localized treatments, it is useful to track any tool deviation from the planned trajectory to minimize positioning errors and procedural complications. The goal is to display tool deflections in real time, with greater bandwidth and accuracy than when viewing the tool in MR images. A standard 18 ga × 15 cm inner needle is prepared using a fixture, and 350-μm-deep grooves are created along its length. Optical fibers are embedded in the grooves. Two sets of sensors, located at different points along the needle, provide an estimate of the bent profile, as well as temperature compensation. Tests of the needle in a water bath showed that it produced no adverse imaging artifacts when used with the MR scanner.