An experimental investigation into the structure of a supersonic jet impinging on a large plate is presented. Digital particle image velocimetry (DPIV), shadowgraph photography and acoustic measurements are used to understand the relationship between the unsteady jet structure and the production of tones for nozzle-to-plate spacings between 1 and 5 nozzle exit diameters at a nozzle–pressure ratio equal to 4. Results indicate that the instability of the jet depends on the location of the plate in the shock cell structure of the corresponding free jet and the strength of the standoff shock wave, rather than on the occurrence of recirculation zones in the impingement region. Phase-locked studies show streamwise displacements of the stand-off shock wave, a moving recirculation zone in the subsonic flow in front of the plate, and significant oscillations of both the compression and expansion regions in the peripheral supersonic flow when tones are produced. Sound is shown to be generated by periodic pulsing of the wall jet boundary resulting from periodic motion of the flow in the impingement and near-wall regions of the flow.
A laser-doppler anemometer was used to obtain flow-field velocity measurements in a 4:1 pressure ratio, 4.54 kg/s (10 lbm/s), centrifugal impeller, with splitter blades and backsweep, which was configured with a vaneless diffuser. Measured through-flow velocities are reported for ten quasi-orthogonal survey planes at locations ranging from 1% to 99% of main blade chord. Measured through-flow velocities are compared to those predicted by a 3-D viscous steady flow analysis (Dawes) code.The measurements show the development and progression through the impeller and vaneless diffuser of a through-flow velocity deficit which results from the tip clearance flow and accumulation of low momentum fluid centrifuged from the blade and hub surfaces. Flow traces from the CFD analysis show the origin of this deficit which begins to grow in the inlet region of the impeller where it is first detected near the suction surface side of the passage. It then moves toward the pressure side of the channel, due to the movement of tip clearance flow across the impeller passage, where it is cut by the splitter blade leading edge. As blade loading increases toward the rear of the channel the deficit region is driven back toward the suction surface by the cross-passage pressure gradient. There is no evidence of a large wake region that might result from flow separation and the impeller efficiency is relatively high. The flow field in this impeller is quite similar to that documented previously by NASA Lewis in a large low-speed backswept impeller.
The standard approach in digital particle image velocimetry (DPIV) data processing is to use fast Fourier transforms to obtain the cross-correlation of two single exposure subregions, where the location of the cross-correlation peak is representative of the most probable particle displacement across the subregion. This standard DPIV processing technique is analogous to matched spatial filtering, a technique commonly used in optical correlators to perform the cross-correlation operation. Phase only filtering is a well-known variation of matched spatial filtering, which when used to process DPIV image data yields correlation peaks which are narrower and up to an order of magnitude larger than those obtained using traditional DPIV processing. In addition to possessing desirable correlation plane features, phase only filters also provide superior performance in the presence of dc noise in the correlation subregion. When DPIV image subregions contaminated with surface flare light or high background noise levels are processed using phase only filters, the correlation peak pertaining only to the particle displacement is readily detected above any signal stemming from the dc objects. Tedious image masking or background image subtraction is not required. Both theoretical and experimental analyses of the signal-to-noise ratio performance of the filter functions are presented. In addition, a new symmetric phase only filtering (SPOF) technique, which is a variation on the traditional phase only filtering technique, is described and demonstrated. The SPOF technique exceeds the performance of the traditionally accepted phase only filtering techniques and is easily implemented in standard DPIV FFT-based correlation processing with no significant computational performance penalty. The SPOF-based optical correlation processing approach is presented as a new paradigm for more robust cross-correlation processing of low signal-to-noise ratio DPIV image data.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.