DNA demonstrates a remarkable capacity for creating designer nanostructures and devices. A growing number of these structures utilize Förster resonance energy transfer (FRET) as part of the device's functionality, readout or characterization, and, as device sophistication increases so do the concomitant FRET requirements. Here we create multi-dye FRET cascades and assess how well DNA can marshal organic dyes into nanoantennae that focus excitonic energy. We evaluate 36 increasingly complex designs including linear, bifurcated, Holliday junction, 8-arm star and dendrimers involving up to five different dyes engaging in four-consecutive FRET steps, while systematically varying fluorophore spacing by Förster distance (R0). Decreasing R0 while augmenting cross-sectional collection area with multiple donors significantly increases terminal exciton delivery efficiency within dendrimers compared with the first linear constructs. Förster modelling confirms that best results are obtained when there are multiple interacting FRET pathways rather than independent channels by which excitons travel from initial donor(s) to final acceptor.

No abstract

As a specific example of the enhancement of enzymatic activity that can be induced by nanoparticles, we investigate the hydrolysis of the organophosphate paraoxon by phosphotriesterase (PTE) when the latter is displayed on semiconductor quantum dots (QDs). PTE conjugation to QDs underwent extensive characterization including structural simulations, electrophoretic mobility shift assays, and dynamic light scattering to confirm orientational and ratiometric control over enzyme display which appears to be necessary for enhancement. PTE hydrolytic activity was then examined when attached to ca. 4 and 9 nm diameter QDs in comparison to controls of freely diffusing enzyme alone. The results confirm that the activity of the QD conjugates significantly exceeded that of freely diffusing PTE in both initial rate (∼4-fold) and enzymatic efficiency (∼2-fold). To probe kinetic acceleration, various modified assays including those with increased temperature, presence of a competitive inhibitor, and increased viscosity were undertaken to measure the activation energy and dissociation rates. Cumulatively, the data indicate that the higher activity is due to an acceleration in enzyme-product dissociation that is presumably driven by the markedly different microenvironment of the PTE-QD bioconjugate's hydration layer. This report highlights how a specific change in an enzymatic mechanism can be both identified and directly linked to its enhanced activity when displayed on a nanoparticle. Moreover, the generality of the mechanism suggests that it could well be responsible for other examples of nanoparticle-enhanced catalysis.

We report the development of high-mobility carbon-nanotube thin-film transistors fabricated on a polymeric substrate. The active semiconducting channel in the devices is composed of a random two-dimensional network of single-walled carbon nanotubes (SWNTs). The devices exhibit a field-effect mobility of 150cm2∕Vs and a normalized transconductance of 0.5mS∕mm. The ratio of on-current (Ion) to off-current (Ioff) is ∼100 and is limited by metallic SWNTs in the network. With electronic purification of the SWNTs and improved gate capacitance we project that the transconductance can be increased to ∼10–100mS∕mm with a significantly higher value of Ion∕Ioff, thus approaching crystalline semiconductor-like performance on polymeric substrates.

The unique properties provided by hybrid semiconductor quantum dot- (QD) bioconjugates continue to stimulate interest for many applications ranging from biosensing to energy harvesting. Understanding both the structure and function of these composite materials is an important component in their development. Here, we compare the architecture that results from using two common self-assembly chemistries to attach DNA to QDs. DNA modified to display either a terminal biotin or an oligohistidine peptidyl sequence was assembled to streptavidin/amphiphilic polymer- or PEG-functionalized QDs, respectively. A series of complementary acceptor dye-labeled DNA were hybridized to different positions on the DNA in each QD configuration and the separation distances between the QD donor and each dye-acceptor probed with Förster resonance energy transfer (FRET). The polyhistidine self-assembly yielded QD-DNA bioconjugates where predicted and experimental separation distances matched reasonably well. Although displaying efficient FRET, data from QD-DNA bioconjugates assembled using biotin-streptavidin chemistry did not match any predicted separation distances. Modeling based upon known QD and DNA structures along with the linkage chemistry and FRET-derived distances was used to simulate each QD-DNA structure and provide insight into the underlying architecture. Although displaying some rotational freedom, the DNA modified with the polyhistidine assembles to the QD with its structure extended out from the QD-PEG surface as predicted. In contrast, the random orientation of streptavidin on the QD surface resulted in DNA with a wide variety of possible orientations relative to the QD which cannot be controlled during assembly. These results suggest that if a particular QD-biocomposite structure is desired, for example, random versus oriented, the type of bioconjugation chemistry utilized will be a key influencing factor.

No abstract

Combining the inherent scaffolding provided by DNA structure with spatial control over fluorophore positioning allows the creation of DNA-based photonic wires with the capacity to transfer excitation energy over distances greater than 150 Å. We demonstrate hybrid multifluorophore DNA-photonic wires that both self-assemble around semiconductor quantum dots (QDs) and exploit their unique photophysical properties. In this architecture, the QDs function as both central nanoscaffolds and ultraviolet energy harvesting donors that drive Förster resonance energy transfer (FRET) cascades through the DNA wires with emissions that approach the near-infrared. To assemble the wires, DNA fragments labeled with a series of increasingly red-shifted acceptor-dyes were hybridized in a predetermined linear arrangement to a complementary DNA template that was chemoselectively modified with a hexahistidine-appended peptide. The peptide portion facilitated metal-affinity coordination of multiple hybridized DNA-dye structures to a central QD completing the final nanocrystal-DNA photonic wire structure. We assembled several such hybrid structures where labeled-acceptor dyes were excited by the QDs and arranged to interact with each other via consecutive FRET processes. The inherently facile reconfiguration properties of this design allowed testing of alternate formats including the addition of an intercalating dye located in the template DNA or placement of multiple identical dye acceptors that engaged in homoFRET. Lastly, a photonic structure linking the central QD with multiple copies of DNA hybridized with 4-sequentially arranged acceptor dyes and demonstrating 4-consecutive energy transfer steps was examined. Step-by-step monitoring of energy transfer with both steady-state and time-resolved spectroscopy allowed efficiencies to be tracked through the structures and suggested that acceptor dye quantum yields are the predominant limiting factor. Integrating such DNA-based photonic structures with QDs can help create a new generation of biophotonic wire assemblies with widespread potential in nanotechnology.

A series of gold nanoclusters stabilized by ligands containing short ethylene oxide oligomers of fixed length were prepared and characterized. The thiols CH3(OCH2CH2) n SH (where n = 2, 3, and 4) were substituted onto the surface of 1.8-nm hexanethiol-capped gold clusters by a thiol-exchange reaction, and the resulting nanoclusters were characterized by NMR, FTIR, and UV/vis spectroscopies; TGA; and TEM analysis. A degree of ligand exchange greater than 99% was achieved, and the gold core diameter remained unchanged in the final material. Of particular interest, the cluster with n = 2 was water-insoluble, whereas those with n = 3 or 4 were water-soluble. The thin-film electrical conductivities of these clusters were compared with those of alkanethiol-capped clusters of similar chain lengths and found to be roughly 1 order of magnitude greater. In a chemical vapor sensor configuration, this series of clusters displayed strong electrical responses that showed a correlation between the length of the ethylene oxide ligand and the polarity of the vapor.