The main purpose of this paper was to obtain a material with efficient adsorbing properties and selectivity, to recover the gold (III) from residual diluted solutions resulted from the electroplating process. In this regard, a material was obtained by physico-chemical functionalization of a chemically inert support with functional groups of nitrogen and carboxyl. As a source of functional groups glutamic acid was used, and Amberlite XAD7 type acrylic resin was used as solid support. In order to establish the mechanism of the adsorption process, kinetic, thermodynamic and equilibrium studies were performed. The maximum adsorption capacity of the material has been established, and a gold (III) recovery process has been proposed using thermal decomposition of the exhausted adsorbed material. Main objective of this study was to evaluate an environmental friendly adsorbent material to recover gold from secondary industrial sources.

The objective of this paper was to evaluate the potential of a new adsorbent material to recover Au (III) from real wastewater, in a column with a fixed bed in a dynamic regime. The material was obtained through functionalization, by impregnation of the commercial resin, Amberlite XAD 7 type, with L-glutamic acid, which has active groups –NH2 and –COOH. The goal of the experiments was to follow the correlation of fixed-bed column specific adsorption parameters (the effluent volume, the amounts of adsorbent, heights of the adsorbent layer in column) with the time necessary to cross the column. The experimental data obtained were modeled, using the Bohart–Adams, Yoon–Nelson Thomas and Clark models, to establish the mechanism of the Au (III) recovery process, in a dynamic regime. Also, we established the number of cycles for adsorption–desorption for which the new material can be used. We used 5% HNO3 (5%) as desorption agent in five adsorption–desorption cycles, until the process was no longer efficient. The degree of desorption varied between 84% and 34% from cycle 1 to cycle 5.

Gold is one of the precious metals with multiple uses, whose deposits are much smaller than the global production needs. Therefore, extracting maximum gold quantities from industrial diluted solutions is a must. Am-L-GA is a new material, obtained by an Amberlite XAD7-type commercial resin, functionalized through saturation with L-glutamic acid, whose adsorption capacity has been proved to be higher than those of other materials utilized for gold adsorption. In this context, this article presents the results of a factorial design experiment for optimizing the gold recovery from residual solutions resulting from the electronics industry using Am-L-GA. Firstly, the material was characterized using atomic force microscopy (AFM), to emphasize the material’s characteristics, essential for the adsorption quality. Then, the study showed that among the parameters taken into account in the analysis (pH, temperature, initial gold concentration, and contact time), the initial gold concentration in the solution plays a determinant role in the removal process and the contact time has a slightly positive effect, whereas the pH and temperature do not influence the adsorption capacity. The maximum adsorption capacity of 29.27 mg/L was obtained by optimizing the adsorption process, with the control factors having the following values: contact time ~106 min, initial Au(III) concentration of ~164 mg/L, pH = 4, and temperature of 25 °C. It is highlighted that the factorial design method is an excellent instrument to determine the effects of different factors influencing the adsorption process. The method can be applied for any adsorption process if it is necessary to reduce the number of experiments, to diminish the resources or time consumption, or for expanding the investigation domain above the experimental limits.

Sustainable waste and water management are key components of the newest EU policy regarding the circular economy. Simple, performant and inexpensive water treatment methods based on reusing waste are prerequisites for human health, sustainable development and environmental remediation. The design of performant, cost-effective absorbents represents a topical issue in wastewater treatment. This study aimed to investigate the development of a newly engineered adsorbent by functionalizing two different types of waste (industrial and food) with magnetic nanoparticles as environmentally friendly, highly efficient, cheap material for cadmium removal from aqueous solutions. This nano-engineered adsorbent (EFM) derived from waste eggshell and fly ash was used to remove the cadmium from the aqueous solution. SEM analysis has demonstrated that magnetite nanoparticles were successfully loaded with each waste. In addition, was obtained a double functionalization of the eggshell particles with ash and magnetite particles. As a result of this, the EFM surface area substantially increased, as confirmed by BET. A comprehensive characterization (BET, FT-IR, SEM, XRD and TGA) was performed to study the properties of this newly engineered adsorbent. Batch experiments were conducted to investigate the influence of different reaction parameters: temperature, pH, contact time, dosage adsorbent, initial concentration. Results showed that cadmium adsorption reached equilibrium in 120 min., at pH 6.5, for 0.25 g of adsorbent. The maximum efficiency was 99.9%. The adsorption isotherms research displayed that the Cd2+ adsorption fitted on the Freundlich model indicated a multi-molecular layer adsorption process. In addition, the thermodynamic study (ΔG < 0, ΔH > 0; ΔS > 0) shows that cadmium adsorption is a spontaneous and endothermic process. The adsorbent kinetic study was described with the pseudo-second-order model indicating a chemisorption mechanism. Desorption results showed that the nano-engineered adsorbent (EFM) can be reused. These data confirmed the possibility to enrich relevant theoretical knowledge in the field of waste recovery for obtaining newly designed adsorbents, performant and inexpensive for wastewater remediation.

Reducing the costs associated with water management, improving water quality and the environment are fundamental requirements of sustainable development. Maintaining the optimal level of phosphorus has a direct impact on water quality and the biological system. Current methods used in tertiary wastewater treatment for phosphorus removal present several disadvantages that influence the final water processing cost. Therefore, it is essential for water quality and food safety to develop ecological, cheap and highly efficient materials. This study reported the first comparative assessment of three different types of materials (magnetic, semiconductors and composite) as environmentally friendly, cheap adsorbents for phosphorus removal from wastewater. Several experiments were done to investigate the influence of adsorbent type, dosage and contact time on the efficiency of the processes. The adsorption process was fast and equilibrium was reached within 150 min. We found that the phosphorus adsorption efficiency on of these materials was higher than the chemical method. The obtained results indicated that specific surface area directly influences the performance of the adsorption process. EDS analysis was used to analyze adsorbents composition and analyze the type and content of elements in the substrate before and after reaction with wastewater.