Purpose Cu/Cu diffusion bonding is characterised by high electrical and thermal conductivity, as well as the mechanical strength of the interconnects. But despite a number of advantages, Cu oxidises readily upon exposure to air. To break through the adsorbed oxide-layer high temperature and pressure, long bonding time and inert gas atmosphere are required during the bonding process. This paper aims to present the implementation of an organic self-assembled monolayer (SAM) as a temporary protective coating that inhibits Cu oxidation. Design/methodology/approach Information concerning elemental composition of the Cu surface has been yielded by X-ray photoelectron spectroscopy (XPS) and Fourier-transform infrared (FTIR) spectroscopy. Two types of substrates (electroplated and sputtered Cu) are prepared for thermocompression bonding in two different ways. In the first case, Cu is cleaned with dilute sulphuric acid to remove native copper oxide. In the second case, passivation with SAM followed the cleaning step with dilute sulphuric acid. Shear strength, fracture surface, microstructure of the received Cu/Cu interconnects are investigated after the bonding procedure. Findings The XPS method revealed that SAM can retard Cu from oxidation on air for at least 12 h. SAM passivation on the substrates with sputtered Cu appears to have better quality than on the electroplated ones. This derives from the results of the shear strength tests and scanning electron microscopy (SEM) imaging of Cu/Cu interconnects cross sections. SAM passivation improved the bonding quality of the interconnects with sputtered Cu in comparison to the cleaned samples without passivation. Originality/value The Cu/Cu bonding procedure was optimised by a novel preparation method using SAMs which enables storage and bonding of Si-dies with Cu microbumps at air conditions while remaining a good-quality interconnect. The passivation revealed to be advantageous for the smooth surfaces. SEM and shear strength tests showed improved bonding quality for the passivated bottom dies with sputtered Cu in comparison to the samples without SAM.
Cu-Cu direct interconnects are highly desirable for the microelectronic industry as they allow for significant reductions in the size and spacing of microcontacts. The main challenge associated with using Cu is its tendency to rapidly oxidize in air. This research paper describes a method of Cu passivation using a self-assembled monolayer (SAM) to protect the surface against oxidation. However, this approach faces two main challenges: the degradation of the SAM at room temperature in the ambient atmosphere and the monolayer desorption technique prior to Cu-Cu bonding. In this paper, the systematic investigation of these challenges and their possible solutions are presented. The methods used in this study include thermocompression (TC) bonding, X-ray photoelectron spectroscopy (XPS), shear strength testing, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX). The results indicate nearly no Cu oxidation (4 at.%) for samples with SAM passivation in contrast to the bare Cu surface (27 at.%) after the storage at −18 °C in a conventional freezer for three weeks. Significant improvement was observed in the TC bonding with SAM after storage. The mean shear strength of the passivated samples reached 65.5 MPa without storage. The average shear strength values before and after the storage tests were 43% greater for samples with SAM than for the bare Cu surface. In conclusion, this study shows that Cu-Cu bonding technology can be improved by using SAM as an oxidation inhibitor, leading to a higher interconnect quality.
Direct metal bonding is a preferred fine-pitch technology for stacking of Si dies in 3D integration. Cu is a metal of choice for direct metal bonding because it is the most common metal for redistribution layer in advanced semiconductor manufacturing, Cu has high conductivity and it is a low cost candidate. However Cu oxidises very fast in air which makes the bonding procedure challenging. In this study we present the novel technique of Cu passivation with temporary protective self-assembled monolayer (SAM). X-ray photoelectron spectroscopy (XPS) analysis was used in order to carry out the chemical analysis of the Cu surface. Contact angle (CA) measurements provided the information about the monolayer formation. The influence of immersion time and storage conditions on the SAM passivation quality was examined. Storage of a coated Cu surface at low-temperature air conditions was found to be a promising technique for a long-term oxidation retarding. We summarize the key substrate parameters that influence SAM protective capability
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.