A novel plasma functionalization process based on the pulsed plasma polymerization of allyl glycidyl ether is reported for the generation of robust and highly reactive epoxy-functionalized surfaces with well-defined chemical properties. Using a multitechnique approach including X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry (ToF-SIMS), infrared spectroscopy (FT-IR), atomic force microscopy (AFM) and ellipsometry, the effect of the plasma deposition parameters on the creation and retention of epoxy surface functionalities was characterized systematically. Under optimal plasma polymerization conditions (duty cycle: 1 ms/20 ms and 1 ms/200 ms), reactive uniform films with a high level of reproducibility were prepared and successfully used to covalently immobilize the model protein lysozyme. Surface derivatization was also carried out with ethanolamine to probe for epoxy groups. The ethanolamine blocked surface resisted nonspecific adsorption of lysozyme. Lysozyme immobilization was also done via microcontact printing. These results show that allyl glycidyl ether plasma polymer layers are an attractive strategy to produce a reactive epoxy functionalized surface on a wide range of substrate materials for biochip and other biotechnology applications.

No abstract

In this work we have prepared surface coatings formulated with the antifungal drug caspofungin, an approved pharmaceutical lipopeptide compound of the echinocandin drug class.

Successful implantation of any biomaterial depends on its mechanical, architectural, and surface properties. Materials with good bulk properties seldom possess the appropriate surface characteristics required for good biointegration. The present study investigates the results of surface modification of a highly porous, fully fluorinated polymeric substrate, expanded poly(tetrafluoroethylene) (ePTFE), with a view to improving the surface bioactivity and hence ultimately its biointegration. Modification involved gamma irradiation-induced graft copolymerization with the monomers monoacryloxyethyl phosphate (MAEP) and methacryloxyethyl phosphate (MOEP) in various solvent systems (water, methanol, methyl ethyl ketone, and mixtures thereof). In order to determine the penetration depth of the graft copolymer into the pores and/or the bulk of the ePTFE membranes, angle-dependent X-ray photoelectron spectroscopy (XPS) and magnetic resonance imaging (MRI) were used. It was found that the penetration depth was critically affected by the choice of monomer and solvent as well as by the technique used to remove dissolved oxygen from the grafting mixture: nitrogen degassing versus vacuum. Difficulties due to the porous nature of the membranes in establishing the lateral position of the graft copolymers were largely overcome by combining data from microattenuated total reflectance Fourier transfer infrared (μ-ATR-FTIR) mapping and time-of-flight secondary ion mass spectrometry (ToF-SIMS) imaging. Results show that the large variation in graft heterogeneity found between different samples is largely an effect of the underlying substrate and choice of monomer. The results from this study provide the necessary knowledge and experimental data to control both the graft copolymer lateral position and depth of penetration in these porous ePTFE membranes.

Poly(ethylene glycol) (PEG) is one of the most extensively studied antifouling coatings due to its ability to reduce protein adsorption and improve biocompatibility. Although the use of PEG for antifouling coatings is well established, the stability and density of PEG layers are often inadequate to provide optimum antifouling properties. To improve on these shortcomings, we employed the stepwise construction of PEG layers onto a silicon surface. Acetylene-terminated alkyl monolayers were attached to nonoxidized crystalline silicon surfaces via a one-step hydrosilylation procedure with 1,8-nonadiyne. The acetylene-terminated surfaces were functionalized via a copper-catalyzed azide-alkyne cycloaddition (CuAAC) reaction of the surface-bound alkynes with an azide to produce an amine terminated layer. The amine terminated layer was then further conjugated with PEG to produce an antifouling surface. The antifouling surface properties were investigated by testing adsorption of human serum albumin (HSA) and lysozyme (Lys) onto PEG layers from phosphate buffer solutions. Detailed characterization of protein fouling was carried out with X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS) combined with principal component analysis (PCA). The results revealed no fouling of albumin onto PEG coatings whereas the smaller protein lysozyme adsorbed to a very low extent.