ObjectivesIn order to address acetabular defects, porous metal revision acetabular components and augments have been developed, which require fixation to each other. The fixation technique that results in the smallest relative movement between the components, as well as its influence on the primary stability with the host bone, have not previously been determined.MethodsA total of 18 composite hemipelvises with a Paprosky IIB defect were implanted using a porous titanium 56 mm multihole acetabular component and 1 cm augment. Each acetabular component and augment was affixed to the bone using two screws, while the method of fixation between the acetabular component and augment varied for the three groups of six hemipelvises: group S, screw fixation only; group SC, screw plus cement fixation; group C, cement fixation only. The implanted hemipelvises were cyclically loaded to three different loading maxima (0.5 kN, 0.9 kN, and 1.8 kN).ResultsScrew fixation alone resulted in up to three times more movement (p = 0.006), especially when load was increased to 100% (p < 0.001), than with the other two fixation methods (C and SC). No significant difference was noted when a screw was added to the cement fixation. Increased load resulted in increased relative movement between the interfaces in all fixation methods (p < 0.001).ConclusionCement fixation between a porous titanium acetabular component and augment is associated with less relative movement than screw fixation alone for all implant interfaces, particularly with increasing loads. Adding a screw to the cement fixation did not offer any significant advantage. These results also show that the stability of the tested acetabular component/augment interface affects the stability of the construct that is affixed to the bone.Cite this article: N. A. Beckmann, R. G. Bitsch, M. Gondan, M. Schonhoff, S. Jaeger. Comparison of the stability of three fixation techniques between porous metal acetabular components and augments. Bone Joint Res 2018;7:282–288. DOI: 10.1302/2046-3758.74.BJR-2017-0198.R1.

Femoral component loosening is a rare but severe complication in total knee arthroplasty. Former studies have repeatedly demonstrated radiolucent lines behind the ventral and dorsal anchoring shields of the femoral components, which has led us to investigate this matter further. Therefore, three different cementing techniques were tested in a group of nine Sawbone samples each. These differed in the amount of cement applied on the femoral component as well as in the pressure application. Computed tomography was performed to evaluate and classify the cement penetration into the bone adjacent to the prosthesis according to the zones defined by the Knee Society scoring system. The results show significantly deeper cement penetration in all zones when a pressurizer is used. In the other two groups, no significant difference in the dorsal bevel cement penetration was noted. Additionally, no difference in ventral and dorsal cement penetrations (Zones 1 and 4) was delineated. In contrast, there was a significant difference in both the ventral bevel (Zone 2) as well as the distal anchoring surface (Zones 5–7). The use of a pressurizer results in greater cement penetration into all anchoring areas. Completely covering the component back surface results in a significantly higher penetration, which is mainly due to differences in volume. These data show significantly improved cementation results when using a pressurizer. Whether this improves the biomechanical properties and ultimately the revision rate requires further investigation.

No abstract

Adequate primary stability of the acetabular revision construct is necessary for long-term implant survival. The difference in primary stability between tantalum and titanium components is unclear. Six composite hemipelvises with an acetabular defect were implanted with a tantalum augment and cup, using cement fixation between cup and augment. Relative motion was measured at cup/bone, cup/augment and bone/augment interfaces at three load levels; the results were compared to the relative motion measured at the same interfaces of a titanium cup/augment construct of identical dimensions, also implanted into composite bone. The implants showed little relative motion at all load levels between the augment and cup. At the bone/augment and bone/cup interfaces the titanium implants showed less relative motion than tantalum at 30% load (p < 0.001), but more relative motion at 50% (p = n.s.) and 100% (p < 0001) load. The load did not have a significant effect at the augment/cup interface (p = 0.086); it did have a significant effect on relative motion of both implant materials at bone/cup and bone/augment interfaces (p < 0.001). All interfaces of both constructs displayed relative motion that should permit osseointegration. Tantalum, however, may provide a greater degree of primary stability at higher loads than titanium. The clinical implication is yet to be seen

Background Kinematic alignment is an alternative approach to mechanical alignment. Kinematic alignment can restore the joint line to its prearthritic condition, and its advocates have suggested it may be associated with other benefits. But this alignment approach often results in tibial components that are placed in varus and femoral components that are placed in valgus alignment, which may result in an increased risk of component loosening because of wear. Like malaligned implant components, kinematically aligned knee implants could increase wear in vivo, but we lack comparative data about wear behavior between these approaches. Questions/purposes (1) Do the different alignment approaches (kinematic, mechanical, and purposefully malaligned components) result in different wear rates in a wear simulator? (2) Do the different alignment approaches lead to different worn areas on the polyethylene inserts in a wear simulator? (3) Do the different alignment approaches result in different joint kinematics in a wear simulator? Methods Mechanical alignment was simulated in a forcecontrolled manner with a virtual ligament structure according to the International Organization for Standardization (ISO 14243-1) using a knee wear simulator. To simulate kinematic alignment, flexion-extension motion, internalexternal torque, and the joint line were tilted by 4°, using a novel mechanical setup, without changing the force axis. The setup includes bearings with inclinations of 4°so that the joint axis of 4°is determined. To verify the angle of 4°, aThe study was financially supported by the nonprofit research foundation Stiftung Endoprothetik, Hamburg, Germany (S 01/20). One of the authors (TR) certifies receipt of personal payments, during the study period, in an amount of less than USD 10,000 from Zimmer Biomet Holdings, in an amount less than USD 10,000 from Aesculap AG/AQ Solutions GmbH, and in an amount less than USD 10,000 from DePuy Synthes as honoraria for lectures. One of the authors (JPK) certifies receipt of personal payments, during the study period, in an amount of less than USD 10,000 from Mathys AG and less than USD 10,000 USD from DePuy Synthes as honoraria for lectures. None of these payments influenced the design and results of the current study. All ICMJE Conflict of Interest Forms for authors and Clinical Orthopaedics and Related Research® editors and board members are on file with the publication and can be viewed on request. Clinical Orthopaedics and Related Research® neither advocates nor endorses the use of any treatment, drug, or device. Readers are encouraged to always seek additional information, including FDA approval status, of any drug or device before clinical use. Ethical approval was not sought for the present study.

In cemented joint arthroplasty, state-of-the-art cementing techniques include high-pressure pulsatile saline lavage prior to cementation. Even with its outstanding importance in cementation, there are surprisingly few studies regarding the physical parameters that define pulsatile lavage systems. To investigate the parameters of impact pressure, flow rate, frequency and the cleaning effect in cancellous bone, we established a standardized laboratory model. Standardized fat-filled carbon foam specimens representing human cancellous bone were cleaned with three different high-pressure pulsatile lavage systems. Via CT scans before and after cleaning, the cleaning effect was evaluated. All systems showed a cleaning depth of at least 3.0 mm and therefore can be generally recommended to clean cancellous bone in cemented joint arthroplasty. When comparing the three lavage systems, the study showed significant differences regarding cleaning depths and volume, with one system being superior to its peer systems. Regarding the physical parameters, high impact pressure in combination with high flow rate and longer distance to the flushed object seems to be the best combination to improve the cleaning of cancellous bone and therefore increase the chances of a deeper cement penetration that is required in cemented joint arthroplasty. In summary, this study provides the first standardized comparison of different lavage systems and thus gives initial guidance on how to optimally prepare cancellous bone for cemented joint arthroplasty.

Cemented implant fixation in total joint arthroplasty has been proven to be safe and reliable with good long-term results. However, aseptic loosening is one of the main reasons for revision, potentially caused by poor cementation with low penetration depth in the cancellous bone. Aim of this prospective laboratory study was, to compare impact pressure and cleaning effects of pulsatile saline lavage to novel carbon dioxide lavage in a standardized carbon foam setup, to determine whether or not additional use of carbon dioxide lavage has any impact on cleaning volume or cleaning depth in cancellous bone. Carbon specimens simulating human cancellous bone were filled with industrial grease and then underwent a standardized cleaning procedure. Specimens underwent computed tomography pre- and post-cleaning. Regarding the impact pressure, isolated carbon dioxide lavage showed significant lower pressure compared to pulsatile saline lavage. Even though the combination of carbon dioxide lavage and pulsatile saline lavage had a positive cleaning effect compared to the isolated use of pulsatile saline lavage or carbon dioxide lavage, this was not significant in terms of cleaning volume or cleaning depth.

Purpose Reconstruction of the medial patellofemoral ligament (MPFL-R) with nonresorbable suture tape (FiberTape ® , FT) is becoming popular. Patella-side ixation of the FT can be performed with suture anchors or via soft-tissue ixation. The aim of this study was to investigate whether patella-side soft-tissue ixation can achieve equivalent primary stability compared to suture-anchor ixation. Methods In ten human, fresh-frozen knee joint specimens (m/f 6/4; age 74 ± 9 a), the MPFL was identiied and dissected near the femoral insertion site. In ive knee joints, the MPFL-R using FT was performed with soft-tissue ixation at the patella (study group; SG), and in ive knee joints, the FT was ixed via suture anchors (control group, CG). All reconstructions were evaluated until load to failure of the patella-side ixation with a displacement rate of 200 mm/min. ResultsThe mean maximum load to failure in the SG was 395.3 ± 57.9 N. All reconstructions failed by complete tearing of the medial patellar retinaculum from its medial patellar margin, but ixation of the FT remained stable. In the CG, the mean maximum load to failure was 239.4 ± 54.5 N and was signiicantly diferent compared to the SG (p = 0.04). All reconstructions failed via pullout of the suture anchors. Stifness and elongation did not difer between the groups, and no failure of the FT was observed in any of the specimens. Conclusion Primary stability of soft-tissue MPFL-R using FT was superior to suture-anchor ixation. Both ixation techniques provided suicient primary stability, superior to previously reported native MPFL tensile strengths. MPFL-R with FT could be a possible alternative procedure for MPFL-R, eliminating potential complications due to autologous tendon graft harvesting.