This study evaluated the influence of silane heat treatment and glass fiber fabrication type, industrially treated (I) or pure (P), on flexural and compressive strength of methacrylate resin bars (BISGMA/TEGDMA, 50/50%). Six groups (n = 10) were created: I-sil: I/silanated; P-sil: P-silanated; I-sil/heat: I/silanated heated to 100°; P-sil/heat: P/silanated heated to 100°; (I: I/not silanated; and P: P/not silanated. Specimens were prepared for flexural strength (10 × 2 × 1 mm) and for compressive strength 9.5 × 5.5 × 3 mm) and tested at 0.5 mm/min. Statistical analysis demonstrated the following for flexural strength (P < 0.05): I-sil: 155.89 ± 45.27BC; P-sil: 155.89 ± 45.27BC; I-sil/heat: 130.20 ± 22.11C; P-sil/heat: 169.86 ± 50.29AB; I: 131.87 ± 15.86C. For compressive strength, the following are demonstrated: I-sil: 1367.25 ± 188.77ab; P-sil: 867.61 ± 102.76d; I-sil/heat: 1162.98 ± 222.07c; P-sil/heat: 1499.35 ± 339.06a; and I: 1245.78 ± 211.16bc. Due to the impossibility of incorporating the stipulated amount of fiber, P group was excluded. Glass fiber treatment with heated silane enhanced flexural and compressive strength of a reinforced dental methacrylate.

Increasing fiber content results in higher flexural and diametral tensile strength of an experimental composite reinforced with glass fibers.

Objective: This factorial randomized clinical trial (RCT) tested the effects of the surgical approach (flapped-FPS vs. flapless-FLS surgery) and loading protocol (delayed-DL vs. immediate-IL) for treatment with a four mini implant mandibular overdenture. Material and Methods:A total of 296 one-piece titanium-zirconium mini-implants were inserted in 74 patients (IL/FLS = 17; IL/FPS = 18; DL/FLS = 20; and DL/ FPS = 19). Outcomes included patient's perceived surgical burdens, clinical time, implant survival, and post-surgical symptoms and complications, assessed immediately after surgery, in the 7-day and 6-week follow-ups.Results: Perceived surgical burdens were relatively low, higher for females, and no difference was found between FPS and FLS surgery. Surgical time was lower for FLS surgery. Overall symptoms were mild after 24 h, and higher for females. Less symptoms were recorded for the FLS surgery compared to the FPS for the delayed loading patients, and FLS surgery was associated with a lower risk of bleeding. No early implant failure was observed until the 6-week follow-up. Delayed was associated with discontinuous use of the prosthesis and poor function. Lower complaint rates were observed for immediate loading regardless of the surgery protocol.Conclusions: Mini implants for mandibular overdenture are a feasible option regardless of surgical access and loading protocol, with high safety and predictable survival rates, and low incidence of post-insertion complications. FLS surgery requires less clinical time and results in easier intraoral prosthetic incorporation of attachments compared to FPS surgeries. Immediate loading did not increase the risk of early implant failure when satisfactory primary stability was achieved.

No abstract

Three-dimensional (3D) printing is increasingly used to fabricate denture base materials. However, information on the effect of simulated brushing and thermocycling on the surface roughness and color stability of 3D-printed denture base materials is lacking. The aim of this study was to evaluate the effect of brushing and thermocycling on the surface roughness and color stability of 3D-printed denture base materials and to compare with those of milled and heat-polymerized denture base resins. Disk-shaped specimens (Ø 10 mm × 2 mm) were prepared from 4 different denture base resins (NextDent Denture 3D+ (ND); Denturetec (SC); Polident d.o.o (PD); Promolux (CNV)) (n = 10). Surface roughness (Ra) values were measured before and after polishing with a profilometer. Initial color coordinates were measured by using a spectrophotometer after polishing. Specimens were then consecutively subjected to simulated brushing (10,000 cycles), thermocycling (10,000 cycles), and brushing (10,000 cycles) again. Ra and color coordinates were measured after each interval. Color differences (ΔE00) between each interval were calculated and these values were further evaluated considering previously reported perceptibility (1.72 units) and acceptability (4.08 units) thresholds. Data were analyzed with Friedman, Kruskal–Wallis, and Mann–Whitney U tests (α = 0.05). Ra (p ≥ 0.051) and ΔE00 (p ≥ 0.061) values among different time intervals within each material were similar. Within each time interval, significant differences in Ra (p ≤ 0.002) and ΔE00 values (p ≤ 0.001) were observed among materials. Polishing, brushing, and thermocycling resulted in acceptable surface roughness for all materials that were either similar to or below 0.2 µm. Color of ND printed resin was affected by brushing and thermocycling. All materials had acceptable color stability when reported thresholds are considered.

No abstract

Disk-shaped specimens were prepared from additively (NX and DT), subtractively (MZ), and conventionally manufactured denture base resins (CV). Surface roughness and color coordinates were measured after polishing, simulated brushing, and coffee thermocycling, while surface roughness was also measured before polishing. Polishing reduced the surface roughness of all materials. Brushing and coffee thermocycling increased the surface roughness of only DT. CV had the highest susceptibility to consecutive brushing and coffee thermocycling as it had the highest surface roughness, which was above the clinically acceptable threshold. All materials had similar stainability; only MZ had perceptible color change after brushing. Even though stainability of tested denture base resins was similar, additively or subtractively manufactured computer-aided design and computer-aided manufacturing (CAD-CAM) resins had smoother surfaces after brushing and coffee thermocycling, regardless of the material. Therefore, complete dentures made out of these CAD-CAM resins may have favorable surface properties in the long term. Graphical abstract

No abstract