In this paper, we present a simple and low-cost technique for fabricating highly stretchable (up to 100% strain) and sensitive (gauge factor of up to 20 000) strain sensors. Our technique is based on transfer and embedment of carbonized patterns created through selective laser pyrolization of thermoset polymers, such as polyimide, into elastomeric substrates (e.g., PDMS or Ecoflex). Embedded carbonized materials are composed of partially aligned graphene and carbon nanotube (CNT) particles and show a sharp directional anisotropy, which enables the fabrication of extremely robust, highly stretchable, and unidirectional strain sensors. Raman spectrum of pyrolized carbon regions reveal that under optimal laser settings, one can obtain highly porous carbon nano/microparticles with sheet resistances as low as 60 Ω/□. Using this technique, we fabricate an instrumented latex glove capable of measuring finger motion in real-time.

Chronic wounds are a major health concern and they affect the lives of more than 25 million people in the United States. They are susceptible to infection and are the leading cause of nontraumatic limb amputations worldwide. The wound environment is dynamic, but their healing rate can be enhanced by administration of therapies at the right time. This approach requires real-time monitoring of the wound environment with on-demand drug delivery in a closed-loop manner. In this paper, a smart and automated flexible wound dressing with temperature and pH sensors integrated onto flexible bandages that monitor wound status in real-time to address this unmet medical need is presented. Moreover, a stimuli-responsive drug releasing system comprising of a hydrogel loaded with thermo-responsive drug carriers and an electronically controlled flexible heater is also integrated into the wound dressing to release the drugs on-demand. The dressing is equipped with a microcontroller to process the data measured by the sensors and to program the drug release protocol for individualized treatment. This flexible smart wound dressing has the potential to significantly impact the treatment of chronic wounds.

Biodegradable nanofibrous polymeric substrates are used to fabricate suturable, elastic, and flexible electronics and sensors. The fibrous microstructure of the substrate makes it permeable to gas and liquid and facilitates the patterning process. As a proof‐of‐principle, temperature and strain sensors are fabricated on this elastic substrate and tested in vitro. The proposed system can be implemented in the field of bioresorbable electronics and the emerging area of smart wound dressings.

The pH level in a chronic wound bed is a key indicative parameter for assessment of the healing progress. Due to their fragility and inability to measure multiple wound regions simultaneously, commercial glass microelectrodes are not well-suited for spatial mapping of the wound pH. To address this issue, we present an inexpensive flexible array of pH sensors fabricated on a polymer-coated commercial paper (palette paper). Each sensor consists of two screen-printed electrodes, an Ag/AgCl reference electrode and a carbon electrode coated with a conductive proton-selective polymeric (polyaniline, PANI) membrane. Laser-machining is used to create a self-aligned passivation layer with access holes that is bonded over the sensing and reference electrodes by lamination technology. Characterization of the pH sensors reveal a linear (r 2 = 0.9734) relationship between the output voltage and pH in the 4-10 pH range with an average sensitivity of −50 mV/pH. The sensors feature a rise and fall time of 12 and 36 s for a pH swing of 8-6-8. The sensor biocompatibility is confirmed with HaCaT immortal human kertinocyte cells.

The development of stretchable sensors has recently attracted considerable attention. These sensors have been used in wearable and robotics applications, such as personalized health-monitoring, motion detection, and human-machine interfaces. Herein, we report on a highly stretchable electrochemical pH sensor for wearable point-of-care applications that consists of a pH-sensitive working electrode and a liquid-junction-free reference electrode, in which the stretchable conductive interconnections are fabricated by laser carbonizing and micromachining of a polyimide sheet bonded to an Ecoflex substrate. This method produces highly porous carbonized 2D serpentine traces that are subsequently permeated with polyaniline (PANI) as the conductive filler, binding material, and pH-sensitive membrane. The experimental and simulation results demonstrate that the stretchable serpentine PANI/C-PI interconnections with an optimal trace width of 0.3 mm can withstand elongations of up to 135% and are robust to more than 12 000 stretch-and-release cycles at 20% strain without noticeable change in the resistance. The pH sensor displays a linear sensitivity of -53 mV/pH (r = 0.976) with stable performance in the physiological range of pH 4-10. The sensor shows excellent stability to applied longitudinal and transverse strains up to 100% in different pH buffer solutions with a minimal deviation of less than ±4 mV. The material biocompatibility is confirmed with NIH 3T3 fibroblast cells via PrestoBlue assays.

In this Research Article, we demonstrate a facile method for the fabrication of porous-carbon/silver nanocomposites using direct laser writing on polymeric substrates. Our technique uses a combination of CO2 laser-induced carbonization and selective silver deposition on a polyimide sheet to create flexible highly conductive traces. The localized laser irradiation selectively converts the polyimide to a highly porous and conductive carbonized film with superhydrophilic wettability. The resulting pattern allows for selective trapping of aqueous silver ionic ink solutions into the carbonized regions, which are converted to silver nanoparticle fillers upon an annealing step. Elemental and surface morphology analysis via XRD and SEM reveals a uniform coating of Ag nanoparticles on the porous carbon. The Ag/C composite lowers the sheet resistance of the original laser carbonized polyimide from 50 to 0.02 Ω/□. The resulting patterns are flexible and electromechanically robust with less than 0.6 Ω variation in resistance after >15000 bending flexion cycles at a radius of curvature of 5 mm. Furthermore, using this technique, we demonstrate the fabrication of a wireless resonant pressure sensor capable of detecting pressures ranging from 0 to 97 kPa with an average sensitivity of -26 kHz/kPa.

Chronic wounds affect over 6.5 million Americans and are notoriously difficult to treat. Suboptimal oxygenation of the wound bed is one of the most critical and treatable wound management factors, but existing oxygenation systems do not enable concurrent measurement and delivery of oxygen in a convenient wearable platform. Thus, we developed a low-cost alternative for continuous O2 delivery and sensing comprising of an inexpensive, paper-based, biocompatible, flexible platform for locally generating and measuring oxygen in a wound region. The platform takes advantage of recent developments in the fabrication of flexible microsystems including the incorporation of paper as a substrate and the use of a scalable manufacturing technology, inkjet printing. Here, we demonstrate the functionality of the oxygenation patch, capable of increasing oxygen concentration in a gel substrate by 13% (5 ppm) in 1 h. The platform is able to sense oxygen in a range of 5–26 ppm. In vivo studies demonstrate the biocompatibility of the patch and its ability to double or triple the oxygen level in the wound bed to clinically relevant levels.

We present a disease-on-a-chip model in which cancer grows within phenotypically normal breast luminal epithelium on semicircular acrylic support mimicking portions of mammary ducts. The cells from tumor nodules developing within these hemichannels are morphologically distinct from their counterparts cultured on flat surfaces. Moreover, tumor nodules cocultured with the luminal epithelium in hemichannels display a different anticancer drug sensitivity compared to nodules cocultured with the luminal epithelium on a flat surface and to monocultures of tumor nodules. The mimicry of tumor development within the epithelial environment of mammary ducts provides a framework for the design and test of anticancer therapies.