Because of the superior sealing characteristics compared to labyrinth seals, brush seals found an increased spread in turbomachinery in recent years. Their outstanding sealing performance results mainly from their flexibility. Thus, a very small gap between the rotor and bristle package can be obtained without running the risk of severe detrimental deterioration in case of rubbing. Rubbing between rotor and seal during operation might occur as a result of e.g. an unequal thermal expansion of the rotor and stator or a rotor elongation due to centrifugal forces or manoeuvre forces. Thanks to the flexible structure of the brush seal the contact forces during a rubbing event are reduced, however the frictional heat input can still be considerable. Particularly in aircraft engines with their thin and lightweight rotor structures the permissible material stresses can easily be exceeded by an increased heat input and thus harm the engine’s integrity. The geometry of the seal has a decisive influence on the resulting contact forces and consequently the heat input. The complex interactions between the geometric parameters of the seal and the heat input and leakage characteristics are not yet fully understood. This paper presents the investigation of the influence of the geometric parameters of a brush seal on the heat input into the rotor and the leakage behaviour. Two seals with different packing densities were tested under relevant engine conditions with pressure differences ranging from 1 to 7 bar, relative surface speeds ranging from 30 to 180 m/s and radial overlaps ranging from 0.1 to 0.4 mm. The transient temperature rise during the rub event was recorded with 24 thermocouples in close proximity to the rub contact embedded in the rotor structure. By comparing the temperature curves with the results of a thermal finite element analysis of the rotor the heat input into the rotor was calculated iteratively. It could be shown that the packing density has a decisive influence on the overall operating behaviour of a brush seal. Furthermore, results are obtained for the heat flux distribution between seal and rotor are shown.
Because of the superior sealing characteristics compared to labyrinth seals, brush seals found an increased spread in turbomachinery in recent years. Their outstanding sealing performance results mainly from their flexibility. Thus, a very small gap between the rotor and bristle package can be obtained without running the risk of severe detrimental deterioration in case of rubbing. Rubbing between rotor and seal during operation might occur as a result of e.g., an unequal thermal expansion of the rotor and stator or a rotor elongation due to centrifugal forces or maneuver forces. Thanks to the flexible structure of the brush seal the contact forces during a rubbing event are reduced; however, the frictional heat input can still be considerable. Particularly, in aircraft engines with their thin and lightweight rotor structures, the permissible material stresses can easily be exceeded by an increased heat input and thus harm the engine's integrity. The geometry of the seal has a decisive influence on the resulting contact forces and consequently the heat input. The complex interactions between the geometric parameters of the seal and the heat input and leakage characteristics are not yet fully understood. This paper presents the investigation of the influence of the geometric parameters of a brush seal on the heat input into the rotor and the leakage behavior. Two seals with different packing densities were tested under relevant engine conditions with pressure differences ranging from 1 to 7 bar, relative surface speeds ranging from 30 to 180 m/s, and radial overlaps ranging from 0.1 to 0.4 mm. The transient temperature rise during the rub event was recorded with 24 thermocouples in close proximity to the rub contact embedded in the rotor structure. By comparing the temperature curves with the results of a thermal finite element (FE) analysis of the rotor the heat input into the rotor was calculated iteratively. It could be shown that the packing density has a decisive influence on the overall operating behavior of a brush seal. Furthermore, results for the heat flux distribution between seal and rotor are shown.
Reducing losses in the secondary air system of gas and steam turbines can significantly increase the efficiency of such machines. Meanwhile, brush seals are a widely used alternative to labyrinth seals. Their most valuable advantage over other sealing concepts is the very small gap between the sealing package and the rotor and thus reduced leakage mass flow. This small gap can be achieved due to the great radial flexibility without running the risk of severe detrimental deterioration in case of rubbing. Rubbing between rotor and seal during operation might occur as a result of e.g., an unequal thermal expansion of the rotor and stator or a rotor elongation due to centrifugal forces or manoeuvre forces. Thanks to the flexible structure of the brush seal, the contact forces during a rubbing event are reduced; however, the frictional heat input can still be considerable. Particularly in aircraft engines with their thin and lightweight rotor structures, the permissible material stresses can easily be exceeded by an increased heat input and thus harm the engine's integrity. The geometry of the seal has a decisive influence on the resulting contact forces and consequently the heat input. This paper is a contribution to further understand the influence of the geometrical parameters of the brush seal on the heat input and the leakage during the rubbing of the seal on the rotor. In this paper, a total of three seals with varied back plate inner diameter are examined in more detail. The experimental tests were carried out on the brush seal test rig of the Institute of Thermal Turbomachinery (ITS) under machine-relevant conditions. These are represented by pressure differences of 1 to 7 bar, surface speeds of 30 to 180 m/s and radial interferences of 0.1 to 0.4 mm. For a better interpretation, the results were compared with those obtained at the static test rig of the Institute of Jet Propulsion and Turbomachinery (IFAS) at the Technical University of Braunschweig. The stiffness, the blow-down and the axial behaviour of the seals as a function of the differential pressure can be examined at this test rig. It could be shown that the back plate inner diameter has a decisive influence on the overall operating behaviour of a brush seal.
This paper discusses the question of heat flux distribution between bristle package and rotor during a rubbing event. A three-dimensional Computational Fluid Dynamics (3D CFD) model of the brush seal test rig installed at the Institute of Thermal Turbomachinery (ITS) was created. The bristle package is modelled as a porous medium with local non-thermal equilibrium. The model is used to numerically recalculate experimentally conducted rub tests on the ITS test rig. The experimentally determined total frictional power loss serves as an input parameter to the numerical calculation. By means of statistical evaluation methods, the ma in influences on the heat flux distribution and the maximum temperature in the frictional contact are determined. The heat conductivity of the rotor material, the heat transfer coefficients at the bristles and the rubbing surface were identified as the dominant factors.
The literature already contains some experimental, analytical and numerical investigations on the rubbing and hysteresis behaviour of brush seals. What the investigations have in common is that they were carried out with new and uncontaminated seals, or that such a condition was assumed. The influence of contamination has not been explicitly investigated yet. Particularly in stationary gas and steam turbines, foreign substances can accumulate on and in the bristle package during steady-state operation. In the case of a rubbing event with a contaminated brush seal, e.g., during shutdown of the machine, the process is not expected to be comparable to that assumed in the presence of a new, uncontaminated seal. The present paper is dedicated to the question of the influence of contamination on the total frictional power loss generated during rubbing and the distribution of heat fluxes in friction contact. For this purpose, rub tests with two seals were carried out on the brush seal test rig of the Institute of Thermal Turbomachinery (ITS) in new conditions. Subsequently, the sealing packages were contaminated with oil or a salt mixture. After the treatment, the rub tests were repeated and compared with the previous tests. In addition, stiffness measurements were used to assess the degree of contamination. A strong influence on the rubbing behaviour by the contamination was detected. Contamination causes the flexibility of the bristle package to be greatly reduced. As a result, especially at the beginning of the first measurements, the total power losses and rotor heat inputs are strongly increased. This flexibility is partly regained in the course of the measurements. As expected, contamination also influences the hysteresis behaviour of the seal. A highly increased leakage rate after rubbing could be observed, because the bristles remained close to their deflected positions. In the case of the salted seal, however, an improvement in the leakage performance could be observed after several repeat tests.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.