This paper suggests a new ultrasonic-based enhanced oil recovery (EOR) model for application in oil field reservoirs. The model is modular and consists of an acoustic module and a heat transfer module, where the heat distribution is updated when the temperature rise exceeds 1 °C. The model also considers the main EOR parameters which includes both the geophysical (i.e., porosity, permeability, temperature rise, and fluid viscosity) and acoustical (e.g., acoustic penetration and pressure distribution in various fluids and mediums) properties of the wells. Extended experiments were performed using powerful ultrasonic waves which were applied for different kind of oils & oil saturated core samples. The corresponding results showed a good matching with those obtained from simulations, validating the suggested model to some extent. Hence, a good recovery rate of around 88.2% of original oil in place (OOIP) was obtained after 30 min of continuous generation of ultrasonic waves. This leads to consider the ultrasonic-based EOR as another tangible solution for EOR. This claim is supported further by considering several injection wells where the simulation results indicate that with four (4) injection wells; the recovery rate may increase up-to 96.7% of OOIP. This leads to claim the high potential of ultrasonic-based EOR as compared to the conventional methods. Following this study, the paper also proposes a large scale ultrasonic-based EOR hardware system for installation in oil fields.

No abstract

No abstract

In this paper an oil-water de-emulsification process within large tanks using ultrasonic technology is presented. As the device would operate in hazardous areas, it should not consume an excessive amount of electrical power. Hence, the paper investigates the suitable oil-water concentrations (10-90% concentrations in step of 10%) which would lead to the fastest separation while consuming the minimum amount of power. Extensive experiments which were conducted using a powerful 20kHz ultrasonic sensor were indicative with good repeatability that the emulsion layer with less water content (i.e. 10 to 40% water-cut) gets significantly faster separation. The experimental study was then validated through a set of finite element-based simulations for different ratios of oil water emulsions. This led to suggest a new feasible de-emulsifying device which consists of a one dimensional array of ultrasonic sensors which are vertically distributed to emit ultrasonic waves in horizontal direction and in a time multiplexed manner.

No abstract

This paper presents a fixed-point reconfigurable parallel VLSI hardware architecture for real-time Electrical Capacitance Tomography (ECT). It is modular and consists of a front-end module which performs precise capacitance measurements in a time multiplexed manner using Capacitance to Digital Converter (CDC) technique. Another FPGA module performs the inverse steps of the tomography algorithm. A dual port built-in memory banks store the sensitivity matrix, the actual value of the capacitances, and the actual image. A two dimensional (2D) core multiprocessing elements (PE) engine intercommunicates with these memory banks via parallel buses. A Hardware-software codesign methodology was conducted using commercially available tools in order to concurrently tune the algorithms and hardware parameters. Hence, the hardware was designed down to the bit-level in order to reduce both the hardware cost and power consumption, while satisfying real-time constraint. Quantization errors were assessed against the image quality and bit-level simulations demonstrate the correctness of the design. Further simulations indicate that the proposed architecture achieves a speed-up of up to three orders of magnitude over the software version when the reconstruction algorithm runs on 2.53 GHZ-based Pentium processor or DSP Ti's Delphino TMS320F32837 processor. More specifically, a throughput of 17.241 Kframes/sec for both the Linear-Back Projection (LBP) and modified Landweber algorithms and 8.475 Kframes/sec for the Landweber algorithm with 200 iterations could be achieved. This performance was achieved using an array of [2×2] × [2×2] processing units. This satisfies the real-time constraint of many industrial applications. To the best of the authors' knowledge, this is the first embedded system which explores the intrinsic parallelism which is available in modern FPGA for ECT tomography.Index Terms -ECT, FPGA, matrix multiplication decomposition. 0018-9340 (c)

No abstract

No abstract