In recent years, piezoelectric materials have been widely investigated for harvesting energy from ambient vibrations. A vibrating piezoelectric device (PD) generates alternating current (AC), which needs to be converted into direct current (DC) for powering electronic devices or for storage. A traditional full-wave bridge rectifier (FBR) interface circuit serves this purpose, but it suffers from high power loss due to the presence of high forward voltage across the diodes. In this paper, an improved H-Bridge rectifier circuit is proposed as the AC-DC rectifier circuit to reduce power loss for high frequency and low amplitude application. The performance of the proposed rectifier circuit was experimentally studied, analysed and discussed. Two different testing scenarios for high frequency, namely, varying input power with fixed excitation frequency and varying excitation frequency with fixed input voltage were considered. Applicability of the circuit at low frequency range was also investigated. The outcome shows that the proposed circuit notably increases the voltage and the power produced from the PD when compared to traditional FBR circuits.

Harvesting energy from human motion for powering small scale electronic devices is attracting research interest in recent years. A piezoelectric device (PD) is capable of harvesting energy from mechanical motions, in the form of alternating current (AC) voltage. The AC voltage generated is of low frequency and is often unstable due to the nature of human motion, which renders it unsuitable for charging storage device. Thus, an electronic circuit such as a full bridge rectifier (FBR) is required for direct current (DC) conversion. However, due to forward voltage loss across the diodes, the rectified voltage and output power are low and unstable. In addition, the suitability of existing rectifier circuits in converting AC voltage generated by PD as a result of low frequency human motion induced non-sinusoidal vibration is unknown. In this paper, an improved H-Bridge rectifier circuit is proposed to increase and to stabilise the output voltage. To study the effectiveness of the proposed circuit for human motion application, a series of experimental tests were conducted. Firstly, the performance of the H-Bridge rectifier circuit was studied using a PD attached to a cantilever beam subject to low frequency excitations using a mechanical shaker. Real-life testing was then conducted with the source of excitation changed to a human performing continuous cycling and walking motions at a different speed. Results show that the H-Bridge circuit prominently increases the rectified voltage and output power, while stabilises the voltage when compared to the conventional FBR circuit. This study shows that the proposed circuit is potentially suitable for PEH from human motion.

This paper describes the design and practical application of a dual-stage H-Bridge (DSHBR) circuit to reduce the rectification losses and mitigate ripples in piezoelectric energy harvesting. The proposed DSHBR circuit integrates both AC-DC and DC-DC conversion processes using bidirectional switches and a step-up DC-DC converter, which applies to both positive and negative half cycles. One additional feature is that it does not require external power to turn on the bidirectional switches (Vth < 0.3 V). Such feature facilitates active rectification at very low AC voltages (Vac < 0.5) generated by the piezoelectric device (PD). To validate the performance of the proposed circuit, a series of experimental tests were conducted. Firstly, the performance of circuit on rectifying the PD output was investigated using a shaker to generate high and low frequency excitations. Next, real-life testing was conducted with human arm motion as the source of excitation. Then, the ability of the entire system to charge solar batteries was investigated. The outcome shows that the DSHBR circuit prominently increased the rectified voltage and the output power while stabilising the DC voltage when compared with the conventional H-Bridge circuit.

This paper describes the detailed modelling of a vibration-based miniature piezoelectric device (PD) and the analysis modes of operation and control of a voltage doubler boost converter (VDBC) circuit to find the PD’s optimal operating conditions. The proposed VDBC circuit integrates a conventional voltage doubler (VD) circuit with a step-up DC-DC converter circuit in modes 1–4, while a non-linear synchronisation procedure of a conventional boost converter circuit is employed in modes 5–6. This integration acted as the voltage boost circuit without utilising duty cycles and complex auxiliary switching components. In addition, the circuit does not require external trigger signals to turn on the bidirectional switches. This facilitates the operation of VDBC circuit at very low AC voltage (Vac ≥ 0.5 V). Besides this, the electrical characteristics of VDBC circuit’s input (i.e., PD) perfectly concurs with the studied testing scenarios using impedance power sources (mechanical shaker). Firstly, the proposed circuit which can rectify the PD’s output was tested at both constant input voltage with varying excitation frequency and constant excitation frequency with varying input voltage. Next, a small-scale solar battery was charged to validate the feasibility of the performance of the proposed VDBC circuit. The proposed circuit achieved a maximum output voltage of 11.7 Vdc with an output power of 1.37 mW. In addition, the rectified voltage waveform is stable due to the sminimisation of the ripples. In addition, the performance of VDBC circuit was verified by comparing the achieved results with previously published circuits in the literature. The results show that the proposed VDBC circuit outperformed existing units as described in the literature regarding output voltage and power. The developed rectifier circuit is suitable for various real-life applications such as energy harvesting and battery charging.

No abstract

Miniaturised piezoelectric devices are emerging energy harvesting sources that are appropriate for various implantable and wearable applications. However, these piezoelectric devices exhibit considerable internal resistance due to their internal impedance, which leads to self-start and low-energy conversion failures. This paper describes a dual-stage boost converter circuit by facilitating self-powering features and boosting the low voltage harvested by the piezoelectric devices into dc. The proposed circuit comprises conversion stages of ac-dc and dc-dc in Stages I and II, respectively. In addition, the proposed circuit does not require employing the auxiliary circuits to generate the train pulses by triggering the bidirectional switches to envelop the current being stored in Stage II and kick-start the self-powered circuit for piezoelectric energy harvesting systems. Theoretical assumptions and control strategies were tested and verified with ideal and impedance input sources. The proposed circuit could convert a low voltage of 3 Vac into 19 Vdc. The maximum attained output power by the proposed circuit was 3.61 mW. The outcome depicted that the proposed circuit boosted the low voltage and outperformed the existing literature circuits in terms of output voltage and power.

No abstract

This paper describes an improved non-linear switching circuit (INLSC) for active rectification of voltage and reduction of ripples in the voltage waveform for the piezoelectric energy harvesting (PEH) system. The proposed converter controls the alternating current (AC) generated by the piezoelectric device (PD) under mechanical vibration. The proposed circuit combines the boost and buck-boost processes through a switching process, which functions in both positive and negative cycles. In addition, it controls the voltage and frequency of the load capacitor. In this process, the passive components in the circuit are energised by being short with the AC voltage using switching signals, which facilitates the active rectification of ultra-low AC voltage. Design considerations, theoretical analysis, simulations and experimental results are presented. It was shown that the circuit was able to control the switching signal and to convert low AC voltage (0.44 Vi) to high direct current (DC) voltage (6.5 Vdc) while achieving an output power of 469 µW which outperforms the existing similar circuits and synchronous rectifier circuit. The ripples in the rectified voltage were also comparatively less. Application-wise, the proposed circuit could power a manually connected 7-segments display, commonly used for traffic applications.