No abstract
The technological principles of low-temperature superconductor production for the magnetic system of the International Thermonuclear Experimental Reactor (ITER) that provides continuity of a superconductor billet in the superconductor production are considered.
Обработка металлов давлением Известия вузов. Цветная металлургия • 5 • 2015 ВведениеВ технике широкое применение находят длинно-мерные триметаллические изделия, получаемые во-лочением. В частности, к ним относятся низкотемпе-ратурные сверхпроводники, включающие оболочку и сердечник из токостабилизирующей меди, а также промежуточный слой, который является компози-том, состоящим из ниобиевых волокон в матрице из высокооловянистой бронзы (рис. 1) [1][2][3].В настоящее время в России создано широкомас-штабное производство низкотемпературных сверх-проводящих материалов для магнитных систем. Это Предложена методика определения оптимальных углов волочильного инструмента для трехкомпонентной заготовки, учитывающая наличие калибрующего пояска волоки и обеспечивающая минимальное значение напряжения волочения. Показано влияние технологических параметров на величину оптимальных углов конусности технологического инстру-мента. Для стандартных волок с фиксированным углом конусности получено соотношение для расчета оптимальной вы-тяжки, обуславливающей минимальные значения напряжения волочения.Ключевые слова: волочение, триметалл, угол волочения, вытяжка, оптимизация. Optimization of drawing technology of trimetallic superconducting compositesA procedure of determining the optimal angles of the drawing tool for a three-component billet, which takes into account the presence of the finishing die cylinder and provides a minimal drawing stress, is proposed. The influence of manufacturing parameters on the magnitude of optimal conicity angles of the manufacturing tool is shown. The relationship for the calculation of the optimal drawing, which provides minimal drawing stress, is found for standard dies with a fixed conicity angle.Keywords: drawing, trimetal, drawing angle, drawing, optimization.Citation: Kolmogorov G.L., Snigireva M.V., Aver'yanova E.M. Optimizatsiya tekhnologii volocheniya trimetallicheskikh sverkhprovodnikovykh kompozitov. Izv. vuzov. Tsvet. metallurgiya.
Обработка металлов давлением Известия вузов. Цветная металлургия • 5 • 2015 ВведениеВ технике широкое применение находят длинно-мерные триметаллические изделия, получаемые во-лочением. В частности, к ним относятся низкотемпе-ратурные сверхпроводники, включающие оболочку и сердечник из токостабилизирующей меди, а также промежуточный слой, который является компози-том, состоящим из ниобиевых волокон в матрице из высокооловянистой бронзы (рис. 1) [1][2][3].В настоящее время в России создано широкомас-штабное производство низкотемпературных сверх-проводящих материалов для магнитных систем. Это Предложена методика определения оптимальных углов волочильного инструмента для трехкомпонентной заготовки, учитывающая наличие калибрующего пояска волоки и обеспечивающая минимальное значение напряжения волочения. Показано влияние технологических параметров на величину оптимальных углов конусности технологического инстру-мента. Для стандартных волок с фиксированным углом конусности получено соотношение для расчета оптимальной вы-тяжки, обуславливающей минимальные значения напряжения волочения.Ключевые слова: волочение, триметалл, угол волочения, вытяжка, оптимизация. Optimization of drawing technology of trimetallic superconducting compositesA procedure of determining the optimal angles of the drawing tool for a three-component billet, which takes into account the presence of the finishing die cylinder and provides a minimal drawing stress, is proposed. The influence of manufacturing parameters on the magnitude of optimal conicity angles of the manufacturing tool is shown. The relationship for the calculation of the optimal drawing, which provides minimal drawing stress, is found for standard dies with a fixed conicity angle.Keywords: drawing, trimetal, drawing angle, drawing, optimization.Citation: Kolmogorov G.L., Snigireva M.V., Aver'yanova E.M. Optimizatsiya tekhnologii volocheniya trimetallicheskikh sverkhprovodnikovykh kompozitov. Izv. vuzov. Tsvet. metallurgiya.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.