UAV Photogrammetry today already enjoys a largely automated and efficient data processing pipeline. However, the goal of dispensing with Ground Control Points looks closer, as dual-frequency GNSS receivers are put on board. This paper reports on the accuracy in object space obtained by GNSS-supported orientation of four photogrammetric blocks, acquired by a senseFly eBee RTK and all flown according to the same flight plan at 80 m above ground over a test field. Differential corrections were sent to the eBee from a nearby ground station. Block orientation has been performed with three software packages: PhotoScan, Pix4D and MicMac. The influence on the checkpoint errors of the precision given to the projection centers has been studied: in most cases, values in Z are critical. Without GCP, the RTK solution consistently achieves a RMSE of about 2-3 cm on the horizontal coordinates of checkpoints. In elevation, the RMSE varies from flight to flight, from 2 to 10 cm. Using at least one GCP, with all packages and all test flights, the geocoding accuracy of GNSS-supported orientation is almost as good as that of a traditional GCP orientation in XY and only slightly worse in Z.

High-resolution Digital Surface Models (DSMs) from unmanned aerial vehicles (UAVs) imagery with accuracy better than 10 cm open new possibilities in geosciences and engineering. The accuracy of such DSMs depends on the number and distribution of ground control points (GCPs). Placing and measuring GCPs are often the most time-consuming on-site tasks in a UAV project. Safety or accessibility concerns may impede their proper placement, so either costlier techniques must be used, or a less accurate DSM is obtained. Photogrammetric blocks flown by drones with on-board receivers capable of RTK (real-time kinematic) positioning do not need GCPs, as camera stations at exposure time can be determined with cm-level accuracy, and used to georeference the block and control its deformations. This paper presents an experimental investigation on the repeatability of DSM generation from several blocks acquired with a RTK-enabled drone, where differential corrections were sent from a local master station or a network of Continuously Operating Reference Stations (CORS). Four different flights for each RTK mode were executed over a test field, according to the same flight plan. DSM generation was performed with three block control configurations: GCP only, camera stations only, and with camera stations and one GCP. The results show that irrespective of the RTK mode, the first and third configurations provide the best DSM inner consistency. The average range of the elevation discrepancies among the DSMs in such cases is about 6 cm (2.5 GSD, ground sampling density) for a 10-cm resolution DSM. Using camera stations only, the average range is almost twice as large (4.7 GSD). The average DSM accuracy, which was verified on checkpoints, turned out to be about 2.1 GSD with the first and third configurations, and 3.7 GSD with camera stations only.

No abstract

Due to the recent improvements of automatic measurement procedures in photogrammetry, multi-view 3D reconstruction technologies are becoming a favourite survey tool. Rapidly widening structure-from-motion (SfM) software packages offer significantly easier image processing workflows than traditional photogrammetry packages. However, while most orientation and surface reconstruction strategies will almost always succeed in any given task, estimating the quality of the result is, to some extent, still an open issue. An assessment of the precision and reliability of block orientation is necessary and should be included in every processing pipeline. Such a need was clearly felt from the results of close-range photogrammetric surveys of in situ full-scale and laboratory-scale experiments. In order to study the impact of the block control and the camera network design on the block orientation accuracy, a series of Monte Carlo simulations was performed. Two image block configurations were investigated: a single pseudo-normal strip and a circular highly-convergent block. The influence of surveying and data processing choices, such as the number and accuracy of the ground control points, autofocus and camera calibration was investigated. The research highlights the most significant aspects and processes to be taken into account for adequate in situ and laboratory surveys, when modern SfM software packages are used, and evaluates their effect on the quality of the results of the surface reconstruction.

In surface mining, rockfall can seriously threaten the safety of personnel located at the base of highwalls and cause serious damage to equipment and machinery. Close-range photogrammetry for the continuous monitoring of rock surfaces represents a valid tool to efficiently assess the potential rockfall hazard and estimate the risk in the affected areas. This work presents an autonomous terrestrial stereo-pair photogrammetric monitoring system developed to observe volumes falling from sub-vertical rock faces located in surface mining environments. The system has the versatility for rapid installation and quick relocation in areas often constrained by accessibility and safety issues and it has the robustness to tolerate the rough environmental conditions typical of mining operations. It allows the collection of synchronised images at different periods with high-sensitivity digital single-lens reflex cameras, producing accurate digital surface models (DSM) of the rock face. Comparisons between successive DSMs can detect detachments and surface movements during defined observation periods. Detailed analysis of the changes in the rock surface, volumes and frequency of the rocks dislodging from the sub-vertical rock surfaces can provide accurate information on event magnitude and return period at very reasonable cost and, therefore, can generate the necessary data for a detailed inventory of the rockfall spatial-temporal occurrence and magnitude. The system was first validated in a trial site, and then applied on a mine site located in NSW (Australia). Results were analysed in terms of multi-temporal data acquired over a period of seven weeks. The excellent detail of the data allowed trends in rockfall event to be correlated to lithology and rainfall events, demonstrating the capability of the system to generate useful data that would otherwise require extended periods of direct observation.