SUMMARY Statement of the Problem:The color stability of resin cements plays a major role in the esthetic performance of porcelain laminate veneers. Some dual-polymerizable resin cements used to bond porcelain laminates were shown to undergo color changes during service. Some recently produced cements are described as being color stable, but scientific data are not available. Clinical RelevanceWhile the studied cements behaved acceptably according to the color change index (∆E), they functioned differently in regards to opacity, especially the self-cure ones.
BackgroundBy an increase in use of composite restorations, some defects are also seen in these restorations, which need to be repaired. Since complete replacement of an old restoration may compromise the tooth structure, repair of defect is a more practical approach if there is no caries recurrence. Risk of pulp injury also decreases as such. One major challenge in restoration repair is to obtain a durable bond between the new and old composite. Laser irradiation has been suggested for surface preparation of old composite. This study aimed to assess the effect of composite surface preparation with Er,Cr:YSGG laser on microtensile bond strength to new composite.Material and MethodsA total of 18 blocks were fabricated in three groups of nanohybrid, microhybrid and Beautiful II giomer measuring 4x7x7 mm and subjected to 10,000 thermal cycles between 5-55°C with 30 seconds of dwell time. The samples were randomly assigned to no surface treatment (etching and bonding) or laser plus etching and bonding groups. Composite cylinders measuring 4x7x7 mm were fabricated of Beautiful, nanohybrid and microhybrid composites on old composite surfaces and subjected to 500 thermal cycles for 50 seconds between 5-55°C with 30 seconds of dwell time. Each block was sectioned into 10 samples and they were subjected to microtensile bond strength test. Data were analyzed using ANOVA and Tukey’s test.ResultsIn all composites, the mean bond strength in laser subgroups was higher than that in control subgroups except for giomer, which showed lower bond strength in laser subgroup. The lowest mean bond strength was noted in repair of Z350XT with Z350XT when the surface of old composite was etched (10.92 MPa). The highest mean bond strength was noted in repair of Z250 with giomer when the old composite surface was irradiated with laser (30.55 MPa).ConclusionsEr,Cr:YSGG laser plus etching increased the bond strength in all groups except for giomer group, which showed a reduction in bond strength. Key words:Composite resins, surface treatment, tensile bond strength, laser, er,cr:ysgg, giomer.
ObjectivesThis study aimed to assess the effect of 38% carbamide peroxide on the microleakage of class V cavities restored with either a silorane-based composite or two methacrylate-based composites.Materials and MethodsA total of 96 class V cavities were prepared on the buccal surface of extracted human teeth with both enamel and dentin margins and were randomly assigned into three groups of Filtek P90 (3M-ESPE) + P90 system adhesive (3M-ESPE)(group A), Filtek Z250 (3M-ESPE) + Adper Prompt L-Pop (3M-ESPE)(group B) and Filtek Z350XT (3M-ESPE) + Adper Prompt L-Pop (group C). Half of the teeth were randomly underwent bleaching (38% carbamide peroxide, Day White, Discus Dental, applying for 15 min, twice a day for 14 day) while the remaining half (control) were not bleached. Dye penetration was measured following immersion in basic fuchsine. Data were statistically analyzed using Kruskal-Wallis and Mann-Whitney U tests at a level of 0.05.ResultsNo significant differences were found between composites in the control groups in enamel (p = 0.171) or dentin (p = 0.094) margins. After bleaching, microleakage of Z250 (in enamel [p = 0.867] or dentin [p = 0.590] margins) and Z350 (in enamel [p = 0.445] or dentin [p = 0.591] margins) did not change significantly, but the microleakage of P90 significantly increased in both enamel (p = 0.042) and dentin (p = 0.002) margins.ConclusionsNo significant differences were noted between the bleached and control subgroups of two methacrylate-based composites in enamel or dentin margins. Microleakage of silorane-based composite significantly increased after bleaching.
Background:Studies have shown a reduction in bond strength of composites and glass ionomer to bleached enamel and dentin. Several methods have been proposed to reverse compromised bond strength.Objective:The aim of this study was to evaluate the effect of delayed bonding and application of antioxidant agent on the bond strength of reinforced self-cured (Fuji IX) and light-cured glass ionomers (Fuji II LC) to bleached dentin.Material:Eighty extracted third molars were randomly divided into 8 groups. Buccal dentin surfaces received different treatments: Two control groups: no treatment + bonding Fuji IX or Fuji II LC. Two immediate bonding groups: bleaching + bonding Fuji IX or Fuji II LC. Two delayed bonding groups: bleaching + 7 days delay + bonding Fuji IX or Fuji II LC. Two sodium ascorbate application groups: Bleaching + application of 10% sodium ascorbate + bonding Fuji IX or Fuji II LC. All samples were tested for shear bond strength. Two-way analysis of variance (ANOVA) was used to compare the mean and standard deviations among groups, followed by the Tukey’s test for significant interaction.Results:No statistically significant difference was detected in shear bond strength of Fuji IX to bleached or normal dentin. Although a significant reduction was found shear bond strength values of Fuji II LC to bleached dentin, no significant difference was observed between no bleaching group and those treated with 10% sodium ascorbate or 7 days of delay in bonding for both types of glass ionomer.Conclusion:Bleaching had no significant effect on shear bond strength of Fuji IX to dentin; this type of GI can be used immediately after bleaching.
Cements with minimum shrinkage and as thin layer as possible should be used. Filling the undercut with glass ionomer cement decreases the stress. Other experimental and clinical studies must follow this research.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.