Herein trimethylsilane (TMS) is demonstrated to be an efficient binding group suitable for construction of metal-molecule-metal (M-mol-M') junctions, in which one of the metal contacts is an atomically flat gold surface and the other a scanning tunnelling microscopy (STM) tip. The molecular component of the M-mol-M' devices is an oligomeric phenylene ethynylene (OPE) derivative Me(3)Si C≡C{C(6)H(4)C≡C}(2)C(6)H(4)NH(2), featuring both Me(3)SiC≡C and NH(2) metal contacting groups. This compound can be assembled into Langmuir-Blodgett (LB) films on Au--substrates by surface binding through the amine groups. Alternatively, low coverage (sub-monolayer) films are formed by adsorption from solution. In the case of condensed monolayers top electrical contacts are formed to STM tips through the TMS end group. In low coverage films, single molecular bridges can be formed between the gold surface and a gold STM tip. The similarity in the I-V response of a one-layer LB film and the single molecule conductance experiments reveals several points of critical importance to the design of molecular components for use in the construction of M-mol-M' junctions. Firstly, the presence of neighbouring π systems does not have a significant effect on the conductance of the M-mol-M' junction. Secondly, in the STM configuration, intermolecular electron hopping does not significantly enhance the junction transport characteristics. Thirdly, the symmetric behaviour of the I-V curves obtained, despite the different metal-molecule contacts, indicates that the molecule is simply an amphiphilic electron-donating wire and not a molecular diode with strong rectifying characteristics. Finally, the conductance values obtained from the amine/TMS-contacted OPE described here are of the same order of magnitude as thiol anchored OPEs, making them attractive alternatives to the more conventionally used thiol-contacting chemistry for OPE molecular wires.

Langmuir films have been fabricated from 4-[4'-(4''-thioacetyl-phenyleneethynylene)-phenyleneethynylene]-aniline (NOPES) after cleavage of the thioacetyl protecting group. Characterization by surface pressure vs area per molecule isotherms and Brewster angle microscopy reveal the formation of a high quality monolayer at the air-water interface. One layer Langmuir-Blodgett (LB) films were readily fabricated by the transfer of the NOPES Langmuir film onto solid substrates. X-ray photoelectron spectroscopy (XPS), surface polarization-modulated infrared reflection-absorption spectroscopy (PM-IRRAS), and quartz crystal microbalance (QCM) experiments conclusively demonstrate the formation of one layer LB films in which the functional group associated with binding to the substrate can be tailored by the film transfer conditions. Using LB methods this molecule could be transferred to gold samples with either the amine or thiol group attached to the gold surface. The amine group is directly attached to the gold substrate (Au-NH(2)-OPE-SH) when the substrate is initially immersed in the subphase and withdrawn during the transfer process; in contrast, monomolecular films in which the thiolate group is attached to the gold substrate (Au-S-OPE-NH(2)) are obtained when the substrate is initially out of the subphase and immersed during the transfer process. The morphology of these films was analyzed by atomic force microscopy (AFM), showing the formation of homogeneous layers. Film homogeneity was confirmed by cyclic voltammetry, which revealed a large passivation of gold electrodes covered by NOPES monolayers. Electrical properties for both polar orientated junctions have been investigated by scanning tunnelling microscopy (STM), with both orientations featuring a nonrectifying behavior.

Langmuir and Langmuir–Blodgett films have been fabricated from an acetylene-terminated phenylene–ethynylene oligomer, namely 4-((4-((4-ethynylphenyl)ethynyl)phenyl)ethynyl)benzoic acid (HOPEA). Characterization of the Langmuir film by surface pressure vs area per molecule isotherms and Brewster angle microscopy reveals the formation of a high quality monolayer at the air–water interface. One layer Langmuir–Blodgett (LB) films were readily fabricated by the transfer of HOPEA Langmuir films onto solid substrates by the withdrawal of the substrate. The deposition mode was Z-type. Quartz crystal microbalance (QCM) experiments confirm the formation of directionally oriented, monolayer LB films, in which the HOPEA molecules are linked to the gold substrate by attachment through the acid group. The morphology of these films was analyzed by atomic force microscopy (AFM), which revealed an optimum transference surface pressure of 18 mN m–1 for the formation of homogeneous films. Cyclic voltammetry also showed a significant blockage of gold electrodes covered by HOPEA monolayers. Electrical properties of HOPEA monolayers sandwiched between a bottom gold electrode and a gold STM (scanning tunneling microscope) tip have been recorded, revealing that the acetylene group is an efficient linker for electron transport. In addition, the STM experiments indicate a nonresonant tunneling mechanism of charge transport through these metal–molecule–metal junctions.

The preparation, characterization and electrical properties of Langmuir-Blodgett (LB) films composed of a symmetrically substituted oligomeric phenylene ethynylene derivative, namely, 4,4'-[1,4-phenylenebis(ethyne-2,1-diyl)]dibenzoic acid (OPE2A), are described. Analysis of the surface pressure versus area per molecule isotherms and Brewster angle microscopy reveal that good-quality Langmuir (L) films can be formed both on pure water and a basic subphase. Monolayer L films were transferred onto solid substrates with a transfer ratio of unity to obtain LB films. Both L and LB films prepared on or from a pure water subphase show a red shift in the UV/Vis spectrum of about 14 nm, in contrast to L and LB films prepared from a basic subphase, which show a hypsochromic shift of 15 nm. This result, together with X-ray photoelectron spectroscopic and quartz crystal microbalance experiments, conclusively demonstrate formation of one-layer LB films in which OPE2A molecules are chemisorbed onto gold substrates and consequently -COO-Au junctions are formed. In LB films prepared on a basic subphase the other terminal acid group is also deprotonated and associates with an Na(+) counterion. In contrast, LB films prepared from a pure water subphase preserve the protonated acid group, and lateral H-bonds with neighbouring molecules give rise to a supramolecular structure. STM-based conductance studies revealed that films prepared from a basic subphase are more conductive than the analogous films prepared from pure water, and the electrical conductance of the deprotonated films also coincides more closely with single-molecule conductance measurements. This result was interpreted not only in terms of better electron transmission in -COO-Au molecular junctions, but also in terms of the presence of lateral H-bonds in the films formed from pure water, which lead to reduced conductance of the molecular junctions.

A nascent metal–molecule–GNP assembly has been fabricated by immersion of a gold-substrate supported monolayer in a solution of gold nanoparticles (GNPs).

In this contribution, a novel method for practical uses in the fabrication of the top contact electrode in a metal/organic monolayer/metal device is presented. The procedure involves the thermally induced decomposition of an organometallic compound, abbreviated as the TIDOC method. Monolayers incorporating the metal organic compounds (MOCs) [[4‐{(4‐carboxy)ethynyl}phenyl]ethynyl]‐(triphenylphosphine)‐gold, 1, or [1‐isocyano‐4‐methoxybenzene]‐[4‐amino‐phenylethynyl]‐gold, 2, were annealed at moderate temperatures (1: 150 °C for 2h and 2: 100 °C for 2 h), resulting in cleavage of the Au‐P or Au‐C bond and reduction of Au(I) to Au(0) as metallic gold nanoparticles (GNPs). These particles are distributed on the surface of the film resulting in formation of metal/molecule/GNP sandwich structures. Electrical properties of these nascent devices were determined by recording I–V curves with a conductive‐AFM. The I–V curves collected from these metal/organic monolayer/GNPs sandwich structures are typical of metal‐molecule‐metal junctions, with no low resistance traces characteristic of metallic short circuits observed over a wide range of set‐point forces. The TIDOC method is therefore an effective procedure for the fabrication of molecular junctions for the emerging area of molecular electronics.

Monomolecular films of an Oligo(phenylene)ethynylene (OPE) derivative [2isocyano-1,3-dimethylbenzene][4-(4′-amino-phenylethynyl)-phenylethynyl]-gold, 1, containing a gold atom in the molecule backbone have been prepared by the Langmuir-Blodgett (LB) method in order to study how the electrical properties can be modulated in monolayers of OPEs by the incorporation of a gold center in their structures. UV-vis reflection spectra of Langmuir monolayers of 1 at the air-water interface reveal strong aurophilic interactions between neighbouring molecules that increase upon compression. Monolayer Langmuir-Blodgett (LB) films were readily fabricated by the transfer of Langmuir films of 1 onto solid substrates. Quartz crystal microbalance (QCM) experiments conclusively demonstrate the formation of monolayer LB films with a high surface coverage. The morphology of these films was analysed by atomic force microscopy (AFM), revealing the formation of homogeneous layers with an optimum surface pressure of transference of 6 mN•m-1. Film homogeneity and integrity was confirmed by cyclic voltammetry, with efficient blocking of gold electrodes by these well-formed monolayers of 1. The electrical properties of LB films of 1 were investigated by scanning tunnelling microscopy (STM) using a 'tip-to-contact' method. Symmetrical, sigmoidal-shaped I-V curves were observed, with analysis of the pseudolinear (Ohmic) region giving a conductance value G = 3.9 10-5 G 0 , which is relatively high for an OPE derivative and may indicate a beneficial role of metal atom incorporation within the wire-like-system.

Langmuir films of 4-{[4-({4-[(trimethylsilyl)ethynyl]phenyl}ethynyl)phenyl]ethynyl} benzenaminium chloride ([1 H]Cl) undergo anion metathesis when assembled on an aqueous auric acid (HAuCl4 ) subphase. Subsequent transfer to solid supports gives well-formed Langmuir-Blodgett (LB) monolayers of [1 H]AuCl4 in which the trimethylsilyl group serves as the surface contacting group. Photoreduction of the aurate on these monolayers leads to the formation of metallic gold nanoislands, which were distributed over the surface of the film. Electrical properties of these nascent devices were determined by recording current-voltage (I-V) curves with conductive atomic force microscopy (c-AFM) using the PeakForce tunneling AFM (PF-TUNA) mode. This gives consistent sigmoidal I-V curves that are indicative of well-behaved junctions free of metallic filaments and short circuits. The photoreduction of a metal precursor incorporated onto monomolecular films is therefore proposed as an effective method for the fabrication of molecular junctions.