Lu, Y., Wang, L., Wang, D., Wang, Y., Zhang, M., Jin, B. and Chen, P. 2011. Male cone morphogenesis, pollen development and pollen dispersal mechanism in Ginkgo biloba L. Can. J. Plant Sci. 91: 971–981. Ginkgo biloba L. is one of the oldest gymnosperms. Male cone morphogenesis, pollen development and dispersal are important for successful pollination and reproduction. In this study, we investigated the development of male cone, pollen and the sporangial wall in detail. The results indicate that: (1) The primordia of male cones and leaves begin to differentiate in early June and remain open until the following March. The male cones then mature and release pollen in mid-April. The male cones are drooped and approximately perpendicular to the leaves during pollination. (2) The microsporocytes develop from the sporogenous cell and form a tetrahedral tetrad after two simultaneous asymmetrically meioses, then produce a matured four-cell pollen after three polar mitotic divisions. The matured pollen is hemispheric in shape with a large aperture area and three pollen wall layers; once released from the microsporangia, the pollen becomes boat-like in shape. (3) The sporangial walls are eusporangiate and consist of epidermis, endothecium and tapetum. The differentiation of the tapetum occurs separately from that of the epidermis and endothecium, and originates from the outermost layer of sporogenous cells. The sporangial walls exhibit shrinkage of the epidermis, fibrous thickening of the endothecium, and enzymic dissolution of the tapetum during pollen dispersal, which contributes to microsporangia opening. Based on these results, we conclude that there many unique and primitive characteristics of the development of the male cones, pollen and sporangial wall of G. biloba. In addition, we also found that the male cones, pollen and sporangial walls have evolved efficient structural and morphological adaptations to anemophily.

Lu, Y., Jin, B., Wang, L., Wang, Y., Wang, D., Jiang, X.-X. and Chen, P. 2011. Adaptation of male reproductive structures to wind pollination in gymnosperms: Cones and pollen grains. Can. J. Plant Sci. 91: 897–906. Wind pollination (anemophily) in gymnosperms is thought to be an ancestral state. Previous studies considered wind pollination to be a largely random phenomenon, but recent evidence suggests that wind-pollinated species have evolved different complex reproductive adaptations for controlling and maximizing the success of wind pollination. However, compared with angiosperms, wind pollination in gymnosperms is poorly understood. We investigated the male reproductive structures of 13 representative gymnosperm species using a scanning electron microscope and digital camera, and analyzed how the morphological characteristics of male cones and pollen facilitate pollination. These characteristics showed a surprising variation between different gymnosperm species in improving pollination success. For example, the relationship between the position of the male cone and the surrounding vegetative structures is adjusted to optimize pollen release. The pollen grains have sacs and papilla and exhibit particular shapes after release from microsporangia, including boat-like, saccate, papilla-like and spheroid shapes, which facilitate pollen dispersal in the air. Taken together, our results suggest that the extensive diversity of male reproductive structures within gymnosperms represents an evolutionary response to long-term selection and results in solutions to the physical restraints of anemophily.

The localized corrosion resistance of nuclear-grade Alloy 800, which is one of the preferred steam generator (SG) heat exchange tube materials of CANDU and PWR reactors, was studied under simulated SG secondary side crevice chemistry conditions at ambient temperature as well as at elevated temperatures. Series of cyclic potentiodynamic polarization tests were performed to study the localized corrosion resistance of Alloy 800 as a function of chloride ion concentration in the SG crevice solution at 40°C, 150°C and 300°C. Based on the experimental results, empirical equations were provided for calculating the pitting potential of nuclear grade Alloy 800 in the SG secondary side crevice chemistries with different levels of chloride concentration at SG layup, startup and operating temperatures.