No abstract

Curaua nanofibers extracted under different conditions were investigated. The raw fibers were mercerized with NaOH solutions; they were then submitted to acid hydrolysis using three different types of acids (H 2 SO 4 , a mixture of H 2 SO 4 /HCl and HCl). The fibers were analyzed by cellulose, lignin and hemicellulose contents; viscometry, X-ray diffraction (XRD) and thermal stability by thermogravimetric analysis (TG). The nanofibers were morphologically characterized by transmission electron microscopy (TEM) and their surface charges in suspensions were estimated by Zeta-potential. Their degree of polymerization (DP) was characterized by viscometry, crystallinity by XRD and thermal stability by TG. Increasing the NaOH solution concentration in the mercerization, there was a decrease of hemicellulose and lignin contents and consequently an increase of cellulose content. XRD patterns presented changes in the crystal structure from cellulose I to cellulose II when the fibers were mercerized with 17.5% NaOH solution. All curaua nanofibers presented a rod-like shape, an average diameter (D) of 6-10 nm and length (L) of 80-170 nm, with an aspect ratio (L/D) of around 13-17. The mercerization of fibers with NaOH solutions influenced the crystallinity index and thermal stability of the resulting nanofibers. The fibers mercerized with NaOH solution 17.5% resulted in more crystalline nanofibers, but thermally less stable and inferior DP. The aggregation state increases with the amount of HCl introduced into the extraction, due to the decrease of surface charges (as verified by Zeta Potential analysis). However, this release presented nanofibers with better thermal stability than those whose acid hydrolysis was carried out using only H 2 SO 4 .

No abstract

The aim of this work was to study the influence of calcium carbonate nanoparticles in both tensile and impact mechanical properties of a polypropylene homopolymer. Four compositions of PP/CaCO 3 nanocomposites were prepared in a co-rotational twin screw extruder machine with calcium carbonate content of 3, 5, 7 and 10 wt. (%) The tests included SEM analyzes together with EDS analyzer and FTIR spectroscopy for calcium carbonate, tensile and impact tests for PP and the nanocomposites. The results showed an increase in PP elastic modulus and a little increase in yield stress. Brittle-to-ductile transition temperature was reduced and the impact resistance increased with the addition of nanoparticles. From the stress-strain curves we determined the occurrence of debonding process before yielding leading to stress softening. Debonding stress was determined from stress-strain curves corresponding to stress in 1% strain. We concluded that the tensile properties depend on the surface contact area of nanoparticles and on their dispersion. Finally we believe that the toughening was due to the formation of diffuse shear because of debonding process.

No abstract

No abstract

ABSTRACT:The effect of processing conditions and elastomer content on the toughening of Polypropylene (PP) by melt blending with styrene/ethylene-butylene/styrene triblock copolymer (SEBS) in a twin-screw extruder has been investigated. The parameters analyzed were: temperature profile, screw speed, and feed rate of the blend components. Their effect was evaluated through the mechanical properties (tensile strength and Izod impact resistance at room temperature) as well as the morphology of the dispersed phase by means of scanning electron microscopy (SEM). The results showed that the impact resistance increases with increasing rotor speed and feed rate and decreases when the temperature profile is increased. The parameter with the greatest effect on the mechanical properties was the variation in rotor speed. Despite the fact that impact resistance as high as 25 times that of neat PP has been achieved with blends containing 20 wt % SEBS, no significant modification in phase morphology has been observed.

Toughening of polyamide 6 (PA6) can be achieved by appropriate addition of an elastomeric matrix phase; however, this leads to a loss of rigidity and mechanical strength. As a result, much research has been directed at obtaining an optimal balance between toughness and rigidity for these thermoplastics. The approach explored here is the formation of nanocomposites from PA6/acrylonitrile-butadiene-styrene (ABS) blends prepared by melt mixing with a modified montmorillonite (Cloisite 1 30B) and styrene/maleic anhydride copolymer as a compatibilizer. The effect of the mixing sequence of the components on the morphology and properties is a primary focus. The morphology and mechanical properties of the materials were characterized by X-ray diffraction, electron microscopy, and tensile and impact testing. Incorporation of the compatibilizer in the PA6/ABS blend increased toughness but decreased rigidity. A significant increase of modulus was observed for the nanocomposite blend compared with the blend or the matrix. This increase was attributed to the exfoliation of organoclay layers in the PA6 matrix phase. It was also observed that the morphology of the ABS dispersed phase was considerably influenced by the mixture sequence.