For the large-scale sustainable implementation of polymer electrolyte membrane fuel cells in vehicles, high-performance electrocatalysts with low platinum consumption are desirable for use as cathode material during the oxygen reduction reaction in fuel cells. Here we report a carbon black-supported cost-effective, efficient and durable platinum single-atom electrocatalyst with carbon monoxide/methanol tolerance for the cathodic oxygen reduction reaction. The acidic single-cell with such a catalyst as cathode delivers high performance, with power density up to 680 mW cm−2 at 80 °C with a low platinum loading of 0.09 mgPt cm−2, corresponding to a platinum utilization of 0.13 gPt kW−1 in the fuel cell. Good fuel cell durability is also observed. Theoretical calculations reveal that the main effective sites on such platinum single-atom electrocatalysts are single-pyridinic-nitrogen-atom-anchored single-platinum-atom centres, which are tolerant to carbon monoxide/methanol, but highly active for the oxygen reduction reaction.

In this article, manganese oxide nanorods with different crystalline structures, i.e., β-MnO2, α-Mn2O3, and a composite of Mn3O4 and α-Mn2O3, were successfully synthesized via controlling the heat-treatment procedure starting from a manganese oxide composite, containing γ-MnOOH and Mn(OH)4. The oxygen reduction reaction (ORR) polarization curves measured by a rotating disk electrode (RDE) setup show that those MnO x catalysts with higher Mn valent states, i.e., γ-MnOOH and Mn(OH)4 composite and β-MnO2, exhibit better catalytic activity toward the ORR than those with lower Mn valences. Furthermore, we testify that the surface Mn valence of MnO x could be tuned by applying proper potential cycling to the MnO x electrode and thus leads to different activities, i.e., the MnO x surface is rich in Mn(II) after treatment at relatively negative potentials, resulting in degradation in ORR activity, while it is rich in Mn(IV) after treatment at positive potentials, resulting in improvement in activity. Compared with the heat-treatment approach, the electrochemical approach is more facile and energy-saving to tune the surface metal valence and thus ORR activity.

Two-dimensional materials based on ternary system of B, C and N are useful ranging from electric devices to catalysis. The bonding arrangement within these BCN nanosheets largely determines their electronic structure and thus chemical and (or) physical properties, yet it remains a challenge to manipulate their bond structures in a convenient and controlled manner. Recently, we developed a synthetic protocol for the synthesis of crumpled BCN nanosheets with tunable B and N bond structure using urea, boric acid and polyethylene glycol (PEG) as precursors. By carefully selecting the synthesis condition, we can tune the structure of BCN sheets from s-BCN with B and N bond together to h-BCN with B and N homogenously dispersed in BCN sheets. Detailed experiments suggest that the final bond structure of B and N in graphene depends on the preferentially doped N structure in BCN nanosheets. When N substituted the in-plane carbon atom with all its electrons configured into the π electron system of graphene, it facilitates the formation of h-BCN with B and N in separated state. On the contrary, when nitrogen substituted the edge-plane carbon with the nitrogen dopant surrounded with the lone electron pairs, it benefits for the formation of B-N structure. Specially, the compound riched with h-BCN shows excellent ORR performance in alkaline solution due to the synergistic effect between B and N, while s-BCN dominant BCN shows graphite-like activity for ORR, suggesting the intrinsic properties differences of BCN nanosheets with different dopants bond arrangement.

Maximizing the platinum utilization in electrocatalysts toward oxygen reduction reaction (ORR) is very desirable for large‐scale sustainable application of Pt in energy systems. A cost‐effective carbon‐supported carbon‐defect‐anchored platinum single‐atom electrocatalysts (Pt1/C) with remarkable ORR performance is reported. An acidic H2/O2 single cell with Pt1/C as cathode delivers a maximum power density of 520 mW cm−2 at 80 °C, corresponding to a superhigh platinum utilization of 0.09 gPt kW−1. Further physical characterization and density functional theory computations reveal that single Pt atoms anchored stably by four carbon atoms in carbon divacancies (Pt‐C4) are the main active centers for the observed high ORR performance.

No abstract

No abstract

No abstract

A ferrocene-based ionic liquid (Fe-IL) is used as a metal-containing feedstock with a nitrogen-enriched ionic liquid (N-IL) as a compatible nitrogen content modulator to prepare a novel type of non-precious-metal-nitrogen-carbon (M-N-C) catalysts, which feature ordered mesoporous structure consisting of uniform iron oxide nanoparticles embedded into N-enriched carbons. The catalyst Fe(10) @NOMC exhibits comparable catalytic activity but superior long-term stability to 20 wt % Pt/C for ORR with four-electron transfer pathway under alkaline conditions. Such outstanding catalytic performance is ascribed to the populated Fe (Fe3 O4 ) and N (N2) active sites with synergetic chemical coupling as well as the ordered mesoporous structure and high surface area endowed by both the versatile precursors and the synthetic strategy, which also open new avenues for the development of M-N-C catalytic materials.