Thermal aging of hydroxy-terminated polybutadiene/isophorone diisocyanate (HTPB/IPDI)-based polyurethane was studied as a function of NCO/OH ratio (1.0 and 0.85). Samples were aged in air ovens at 50, 60, 65, and 70 °C for periods of time from 1 to 34 weeks. Changes in chemical (swelling testing and FT-IR spectroscopy) and mechanical (tension testing and hardness) properties were evaluated throughout the aging assays. Correlation between equilibrium swelling ratio and elastic modulus, coupled with changes in FT-IR spectra, indicated oxidative cross-linking as the dominant mechanism for both molar ratios investigated. However, determination of Arrhenius activation energy resulted in values of (82 ± 10) kJ.mol -1 and (156 ± 30) kJ.mol -1 for 1.0 and 0.85 NCO/OH ratios, respectively, thus revealing faster oxidative degradation kinetics for higher urethane linkage networks.
The effect of copper and zinc ions on sulphur oxidation by Acidithiobacillus thiooxidans, strain SFR01, isolated from anaerobic sewage sludge was assessed, resulting in tolerance levels up to 20 and 200 mmol l )1 for copper and zinc, respectively. The tolerance levels obtained were higher than the concentration of copper and zinc usually found in the collected sewage sludge. The tolerance levels obtained indicate no constraints for sludge bioleaching of those metals due to their toxicities to the indigenous A. thiooxidans.
The effects of anaerobic digestion and initial pH on the bioleaching of metals from sewage sludge were investigated in shake flask experiments. A strain of Acidithiobacillus thiooxidans was employed in the assays using secondary and anaerobic sludges, which resulted in similar solubilization yields of the metals chromium, copper, lead, nickel, and zinc for both the sludges investigated. The effect of initial pH (7.0 and 4.0) on metal bioleaching was assayed by using the anaerobic sludge inoculated with indigenous sulfur-oxidizing thiobacilli. Although the time required to reach the end of the experiment (final pH close to 1.0) was shortened at initial pH of 4.0, final metal solubilization was not significantly different for both initial pH values, resulting in higher solubilization yields for copper, nickel, and zinc (higher than 80%). Chromium and lead presented solubilization yields close to 50%. The results obtained in this work showed that the metal bioleaching process can be applied to sewage sludge regardless of the type of sludge and without the requirement of pH adjustment.
The effects of metal bioleaching on nutrient solubilization, especially nitrogen and phosphorous, from anaerobically-digested sewage sludge were investigated in this work. The assessment of the sanitary quality of the anaerobic sludge after bioleaching was also carried out by enumerating indicator (total coliforms, fecal coliforms, and fecal streptococci) and total heterotrophic bacteria. The experiments of bioleaching were performed using indigenous sulphur-oxidizing bacteria (Thiobacillus spp.) as inoculum and samples of anaerobically-digested sludge. Nitrogen and phosphorous solubilization from sewage sludge was assessed by measuring, respectively, the concentration of Total Kjeldahl Nitrogen, ammonia, nitrate/nitrite, and soluble and total phosphorous before and after the bioleaching assays. At the end of the experiment, after 4 days of incubation (final pH of 1.4), the following metal solubilization yields were obtained: zinc, 91%; nickel, 87%; copper, 79%; lead, 52%; and chromium, 42%. As a result of sludge acidification, the viable counts of selected indicator bacteria were decreased to below the detection limit (4 x 10(3) cfu 100 ml(-1)), followed by an increase in the mineral fraction of nitrogen (from 6 to 10%) and in the soluble fraction of phosphorous (from 15 to 30%). Although some loss of sludge nutrients can occur during solid-liquid separation following bioleaching, its beneficial effects as metal removal and reduction of pathogenic bacteria are sufficient to consider the potential of this treatment before sludge disposal onto agricultural fields.
Thermal aging of hydroxy-terminated polybutadiene (HTPB) stabilized with 2,6-di(tert-butyl)hydroxytoluene (BHT) was carried out at 60 o C from 1 to 11 weeks. Samples of 200 mL were stored in sealed 500-mL Erlenmeyer flasks under atmospheric pressure or vacuum and periodically withdrawn for physical and chemical analysis, infrared spectroscopy characterization and measurement of HTPB/IPDI (isophorone diisocyanate) reactivity, expressed as pot life. Mechanical properties of the cured polyurethane, prepared from aged HTPB, were assayed by uniaxial tension tests. Despite the unchanged chemical structure, an increase in HTPB/IPDI binder reactivity was observed, being correlated with BHT depletion measured as color change (yellowing). Aging of HTPB showed no interference on mechanical properties of the cured polyurethane.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.