No abstract

Within the limits of this study, optimal detection of chemically simulated pericircumferential implant crestal bone defects is achieved at the least radiation detriment using the smallest FOV, the highest number of acquisition frames, and the smallest voxel.

Objectives: A wide variety of manifestations is presented in patients with Gaucher's disease (GD), including bone, haematology and visceral disturbances. This study was conducted to ascertain the main maxillofacial abnormalities by means of clinical survey, panoramic and cone beam CT (CBCT); to compare the patient's group with an age-sex matched control group; and to correlate clinical and radiological data. Methods: Ten patients previously diagnosed with GD were submitted to clinical and radiological surveys (CBCT and panoramic radiographs). The examination consisted of anamnesis, extra-and intraoral examinations and analyses of each patient's records. Imaging data were collected from the point of view of 3 observers, and the results compared with a healthy group (20 individuals) by means of statistical analysis (Fisher's exact test). Results: Gaucher patients had significantly more manifestations than otherwise healthy carriers. The most prevalent findings were enlarged marrow spaces, generalized osteopenia and effacement of jaw structures (mandibular canal, lamina dura and mental foramen). Here we describe a case in which thickening of the maxillary sinus mucosa was observed on CBCT rather than opacification of the sinus as seen on panoramic radiographs. Pathological fractures, root resorption and delay on tooth eruption were not observed. Conclusions: A poor relationship could be observed between clinical and radiological data. Patients showed important bone manifestations, which require careful diagnostic and surgical planning whenever necessary. Although panoramic radiographs have shown significant differences, CBCT is more effective in pointing out differences between patients and a control group, thus showing it as an important tool for evaluation of Gaucher patients.

No abstract

No abstract

No abstract

Objective: The purpose of this study was to compare the precision and accuracy of linear measurements for Le Fort I osteotomy performed by two different imaging software programs and obtained from three-dimensional cone beam CT (3D-CBCT) images. Methods: The study population consisted of 11 dried skulls submitted to CBCT, which generated 3D images. Linear measurements were based on craniometric anatomical landmarks pre-defined by the authors as specifically used for Le Fort I osteotomy and were identified by two radiologists twice each, independently, using Vitrea 3.8.1 (Vital Images Inc., Plymouth, MN) and open-source digital imaging communication in medicine viewer OsiriX 1.2 64-bit (Pixmeo, Geneva, Switzerland). Subsequently, a third examiner made physical measurements using a digital caliper (167 series; Mitutoyo Sul Americana Ltd, Suzano, SP, Brazil). Results: The results demonstrated a statistically significant difference between OsiriX and the gold standard, especially in the pterygoid process (TPtg L 5 0.019, LLpPtg R 5 0.016 and LLpPtg L 5 0.012). Vitrea showed no statistical difference in comparison with the gold standard, and showed a high level of accuracy in all the measurements performed. The major difference found was 0.42 mm (LLpPtg R). Interexaminer analysis ranged from 0.90 to 0.97 using Vitrea and from 0.8 to 0.97 using OsiriX. Intraexaminer correlation coefficient ranged from 0.90 to 0.98 and from 0.84 to 0.98 for Examiners 1 and 2, respectively, using Vitrea and from 0.93 to 0.99 for Examiner 1 and from 0.64 to 0.96 for Examiner 2 using OsiriX. Conclusion: Vitrea may be considered as precise and accurate, insofar as it was able to perform all the 3D linear measurements. On the other hand, linear measurements performed using OsiriX were not successful in producing accurate linear measurements for Le Fort I osteotomy.

The purpose of this study was to analyze four different cone-beam computed tomography (CBCT) protocols to identify horizontal root fractures (HRF) in endodontically treated teeth, with or without the presence of a metallic post. Thirty extracted single-rooted human premolars were treated endodontically. Afterwards, an observer induced a horizontal fracture in 15 teeth. Each tooth was inserted in an empty mandibular socket and submitted to a computed tomography scan taken with and without the metallic post. The acquisition followed four different protocols, with different fields of view (FOV) and voxel sizes, as follows: FOV 6X16 cm/0.2 mm voxel; FOV 6X16 cm/0.25 mm voxel; FOV 8X8 cm/0.2 mm voxel; FOV 8X8 cm/0.25 mm voxel. Two observers checked all the acquisitions within a two-week interval, and the values of sensitivity, specificity, accuracy and kappa were calculated. The sensitivity, specificity and accuracy values were better for the 8X8 cm/0.2 mm and 16X6 cm/0.25 mm protocols, ranging from 0.60 to 0.86 and 0.53 to 0.80, respectively. The intra-and interobserver concordance ranged from 0.65 to 0.72. The protocols where FOV and voxel were proportional showed better results. The 8x8 cm/0.2 mm protocol had the least interference from the metallic artifact. All four protocols showed a decline in values in the presence of the metallic artifact.