In the last few decades, consumers' growing attention to the close relationship between health and nutrition is emerging as a new trend, mostly regarding the incorporation of natural ingredients into food. Among those ingredients, microalgae are considered as innovative and promising compounds, rich in valuable nutrients and bioactive molecules. In the present work, 3D printed cookies were fortified with the microalga Arthrospira platensis aiming at developing a new functional food with antioxidant properties. A. platensis antioxidants were recovered using ultrasound-assisted extraction in hydroalcoholic solutions. Ethanol/water and biomass/solvent ratios were optimised through a Design of Experiments (DOE) approach, using the antioxidant activity (ORAC and ABTS) and total phenolic content (TPC) as response variables. The highest ORAC, ABTS and TPC values were observed in the extract obtained with 0% ethanol and 2.0% biomass; thus, this extract was chosen to be incorporated into a printable cookie dough. Three different incorporation approaches were followed: (1) dried biomass, (2) freeze-dried antioxidant extract and (3) antioxidant extract encapsulated into alginate microbeads to enhance the stability to heat, light, and oxygen during baking and further storage. All dough formulations presented shape fidelity with the 3D model. The cookies had a w values low enough to be microbiologically stable, and the texture remained constant after 30 days of storage. Moreover, the extract encapsulation promoted an improvement in the ORAC value and colour stability when compared to all other formulations, revealing the potential of A. platensis for the development of a functional 3D food-ink.

Organosolv lignin was incorporated in carboxymethyl cellulose (CMC)-based films as a reinforcing and bioactive agent. Films were produced by the casting method using compatible and environmentally friendly solvents. The incorporation of lignin in CMC-based films was evaluated in term of morphology, physicochemical, barrier, mechanical and antioxidant properties. Solubility tests showed that lignin improved the water resistance of the films for approx. 60%. This behavior was also observed for the water vapor permeability, achieving a 20% reduction. Morphological characteristics suggested low compatibility between organosolv lignin and CMC matrix, revealed by the small aggregates homogeneously distributed in the film, through scanning electron microscopy, related to the self-assembly behavior of lignin. CMC/lignin-based films also presented higher thermal stability. Fourier transform infrared spectroscopy showed that incorporation of lignin led to small changes in the film's structure. Finally, organosolv lignin proved to be a promising material for the development of active CMCbased films due to its demonstrated antioxidant activity that can be useful to pack food products that suffer from undesirable oxidation reactions.

In this work rhamnolipids were evaluated as surfactants for the production of nanostructured lipid carriers (NLCs). NLCs were produced by melt-emulsification using ultra-homogenisation followed by ultrasonication and different ratios of medium-chain-triglycerides and glycerol monostearate (lipid phase) were tested. NLCs presented sizes and polydispersity index values ranged between 97 and 120 nm and 0.20-0.26, respectively. Transmission electron microscopy observations confirmed the size and the spherical morphology of the NLCs. The thermal analysis and X-ray diffraction showed that the amount of solid lipid (glycerol monostearate) influences the melting, crystallisation and enthalpy of NLCs and their degree of crystallinity. Results showed that NLCs were more stable at 4 • C and the best formulation (1% of water phase, 0.05% of biosurfactant and solid: liquid ratio of 10:90) was stable for 30 days. This work showed the possibility of using rhamnolipids to produce NLCs and represent an important step for the development of lipid-based nanosystems using biosurfactants.

Lignin particles (LPs) have gained prominence due to their biodegradability and bioactive properties. LP production at nano and micro scale produced from organosolv lignin and the understanding of size's effect on their properties is unexplored. This work aimed to produce and characterize lignin nanoparticles and microparticles using a green synthesis process, based on ethanol-solubilized lignin and water. Spherical shape LPs, with a mean size of 75 nm and 215 nm and with a low polydispersity were produced, as confirmed by transmission electron microscopy and dynamic light scattering. LPs thermal stability improved over raw lignin, and the chemical structure of lignin was not affected by the production method. The antimicrobial tests proved that LPs presented a bacteriostatic effect on Escherichiacoli and Salmonella enterica. Regarding the antioxidant potential, LPs had a good antioxidant activity that increased with the reaction time and LPs concentration. LPs also presented an antioxidant effect against intracellular ROS, reducing the intracellular ROS levels significantly. Furthermore, the LPs showed a low cytotoxic effect in Caco-2 cell line. These results showed that LPs at different scales (nano and micro) present biological properties and are safe to be used in different high value industrial sectors, such as biomedical, pharmaceutical and food.

Nowadays, one of the strongest factors affecting consumers’ choice at the moment of purchasing food products is their nutritional features. The population is increasingly aware of the diet–health relationship and they are opting for a healthy lifestyle. Concerns with the increasing number of heart-related diseases, which are associated to the consumption of fats, are placing the functional food market in a relevant growth position. Considering that, our goal was to develop, under semi-industrial processing conditions, a healthy meat-based spreadable product (pâté) with reduced fat content through replacement of pork fat by healthier structured oil. Beeswax was used to develop an edible oleogel based on linseed oil with a high content of linolenic acid. A decrease of the hardness and adhesivity was verified for pâtés with oleogel incorporation. Linseed oil inclusion was the main factor leading to an increase of polyunsaturated fatty acids (PUFA) content in pâté samples. A decrease up to 90% in the n-6/n-3 (omega-6/omega-3) ratio can signify a better nutritional value of the obtained pâté samples, which can result in a possible upsurge in omega-3 bioavailability through digestion of these pâtés. This could be an interesting option for the consumption of n-3 polyunsaturated fatty acids, targeting, for example, the reduction of cardiovascular diseases.