No abstract

A core-shell amino-functionalized glycidyl methacrylate magnetic molecularly imprinted polymer (MIP) was synthesized by the suspension polymerization/surface imprinting method and characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), mercury porosimetry, nitrogen gas adsorption–desorption, and elemental analysis. This MIP was used as the sorbent in dispersive solid-phase microextraction (DSPME) of aniline from textile wastewater prior to high-performance liquid chromatography-mass spectrometry (HPLC-MS) measurements. Since aniline is toxic and a probable human carcinogen, its determination in water is of great significance. This is a challenging task because aniline is usually present at trace levels. The effects of different DSPME variables on the preconcentration efficiency have been studied by using the Plackett–Burman screening design of experiments (DoE) followed by response surface methodology optimization using the Box-Behnken design. Thus, DoE enabled the investigation of several variables simultaneously. Under optimized conditions, aniline was effectively and selectively separated by a small amount of the DSPME sorbent and detected in real textile wastewater samples. The method detection limit of 1 ng mL−1 was attained, with good method linearity and acceptable recovery and precision. The results showed that the studied MIP could be a reliable DSPME sorbent for efficiently analyzing trace aniline in real wastewater samples.

An amino-functionalized magnetic macroporous copolymer of glycidyl methacrylate (GM) and ethylene glycol (E) dimethacrylate (m-poly(GME)-deta) was synthesized, fully characterized, and used to investigate the adsorption of vanadium (V) oxyanions from aqueous solutions (Ci = 0.5 mM) in a batch system at room temperature (298 K). Pseudo-first-order (PFO), pseudo-second-order (PSO), Elovich, and intra-particle diffusion (IPD) models were used to analyze the kinetic data. The study showed that sorption is rapid, i.e., the sorption half-time is approximately one minute. Initially, the sorption process primarily involved surface sorbent particles, and it was best described by the PSO model. However, after saturation of the surface active sites is attained, the sorption rate decreases significantly because of limitations of the diffusion rate, which is then primarily controlled by the IPD process. The sorption process is favorable in the pH range of 3–6 due to the strong electrostatic interactions between the absorption centers of copolymer and vanadium (V) oxyanions. In the stated pH range, deta absorption centers with two and three protonated N atoms are in equilibrium as studied by quantum chemical modeling. Among V(V) species present in diluted aqueous media, the adsorption of H2VO4− ions dominates.

No abstract

The industrialization and urbanization expansion have increased the demand for precious and rare earth elements (REEs). In addition, environmental concerns regarding the toxic effects of heavy metals on living organisms imposed an urgent need for efficient methods for their removal from wastewaters and aqueous solutions. The most efficient technique for metal ions removal from wastewaters is adsorption due to its reversibility and high efficiency. Numerous adsorbents were mentioned as possible metal ions adsorbents in the literature. Chelating polymer ligands (CPLs) with adaptable surface chemistry, high affinity towards targeted metal ions, high capacity, fast kinetics, chemically stable, and reusable are especially attractive. This review is focused on methacrylate-based magnetic and non-magnetic porous sorbents. Special attention was devoted to amino-modified glycidyl methacrylate (GMA) copolymers. Main adsorption parameters, kinetic models, adsorption isotherms, thermodynamics of the adsorption process, as well as regeneration of the polymeric sorbents were discussed.

Polymer-based, highly porous nanocomposites with functionalized ligands attached to the core structure are extremely efficient in the detection, removal and recovery of metals through the process of sorption. Quantumchemical models could be helpful for sorption process analyses. The sorption of Cu(II) ions by amino-functionalized chelating macroporous copolymers poly(GMA-co-EGDMA)-amine and sorption selectivity of the subject copolymers, ethylenediamine (en), diethylenetriamine (dien) and triethylenetetramine (trien), were successfully modelled by quantum chemical calculations. Considering the crystal structures from CSD and experimental conditions during the formation of metal complexes, the most frequent mononuclear complexes are those with the tetradentate teta ligand, while binuclear complexes are formed when the metal ion is in large excess. Although the en-copolymer was the most effective functionalized one, higher maximum sorption capacities (Qmax) were observed for the dien- and trien-copolymers, due to their abilities to form binuclear complexes. The enthalpy term has the greatest contribution to the total Gibbs energy change of reaction for the formation of mononuclear Cu(II) complexes (?Gaq), while the solvation energy of the reaction has the greatest contribution in the formation of binuclear complexes. The results of the study indicate that small amines with the ability to form binuclear complex are the best choice for functionalization of the considered copolymer. [Projects of the Serbian Ministry of Education, Science and Technological Development, Grant no. OI 172043, Grant no. 172023 and Grant no. III 43009]

A novel magnetic polymer/bentonite composite was prepared by suspension copolymerization of glycidyl methacrylate and ethylene glycol dimethacrylate in the presence of magnetic bentonite (MB-PGME) and functionalized with ethylene diamine and hexamethylene diamine (MB-PGME-ED and MB-PGME-HD). The obtained samples were characterized in terms of structure as well as thermal, magnetic and morphological properties. The sorption of rhenium (Re) and tungsten (W) from aqueous solution onto MB-PGME-ED and MB-PGME-HD was investigated considering their contact time and different initial ion concentration, giving possibility for usage of these composites as commercial sorbents. The sorption system follows the pseudo-second order and intraparticle diffusion kinetic models. The results indicated a better fit with the Freundlich isotherm model.

A new magnetic amino-functionalized polymeric sorbent based on glycidyl methacrylate was synthesized and used in the separation of chromium Cr(VI) oxyanions sorption from aqueous solutions in a static batch system. The kinetic and isothermal parameters of the sorption process were determined. The experimental data were best fitted by a pseudo-second-order model with R2 = 0.994 and χ2 = 0.004. The sorption process of Cr(VI) removal by amino-functionalized sorbent was controlled by both intraparticle diffusion and liquid film diffusion. The equilibrium results showed that the sorption process is best described by the Freundlich model, followed closely by the Sips isotherm model, with a maximum sorption capacity of 64 mg/g. Quantum chemical modeling revealed that the sorption sites on the sorbent surface are fragments with diethylenetriamine and aminopropyl silane groups that coated the magnetic nanoparticles. The calculations showed that Cr(VI) oxyanions (Cr2O72−, CrO42− and HCrO4−) bind to both sorption sites, with diethylenetriamine centers slightly favored. The X-ray photoelectron spectroscopy (XPS) spectra demonstrate that the chromium bound to the sorbent in the form of Cr(III), indicating that the Cr(VI) can be converted on the surface of the sorbent to a less harmful form Cr(III) due to the sorbent’s chemical composition.