BACKGROUND This article reports the synthesis and characterisation of titanium dioxide‐coated biochar composites (TBCs) by pyrolysing titanium dioxide‐treated biomass prepared by a modified sol–gel method. Their adsorptive and photocatalytic activities were evaluated based on the removal of safranine T (ST) from an aqueous solution with/without UV‐light irradiation. RESULTS Characterisation studies suggested that TiO2 was successfully loaded on the biochar substrate. The biochar and TiO2 contents of the composite significantly affected its performance. The ST removal capabilities of the TBCs with 1, 1.5, 2, and 2.5 g of the biomass are 1.7, 2.3, 7.2, and 2.3 times better than that of the raw biochar, respectively. Thus, the optimum amount of biomass in TBC‐x was determined to be 2 g, with the corresponding sample exhibiting excellent stability, effectiveness over a wide pH range, and a maximum ST removal capacity of 226.7 mg g‐1. CONCLUSION The loading of TiO2 significantly enhanced the adsorption performance of biochar and the high specific surface area of the biochar synergistically promoted the photocatalytic activity of TiO2. Both adsorption and photocatalytic degradation were confirmed to contribute to the decolourisation of the aqueous solution because of the removal of ST, with the effect of adsorption being slightly higher than that of photocatalysis. The synthesised composite is a promising alternative material for removing chemical contaminants. © 2017 Society of Chemical Industry

Parkinson’s disease (PD) is a common neurodegenerative disease featured by progressive degeneration of nigrostriatal dopaminergic neurons (DA) accompanied with motor function impairment. Accumulating evidence has demonstrated that natural compounds from herbs have potent anti-PD efficacy in PD models. Among those compounds, resveratrol, a polyphenol found in many common plants and fruits, is more effective against PD. Resveratrol has displayed a potent neuroprotective efficacy in several PD animal models. However, there is still no systematic analysis of the quality of methodological design of these studies, nor of their results. In this review, we retrieved and analyzed 18 studies describing the therapeutic effect of resveratrol on PD animal models. There are 5 main kinds of PD rodent models involved in the 18 articles, including chemical-induced (MPTP, rotenone, 6-OHDA, paraquat, and maneb) and transgenic PD models. The neuroprotective mechanisms of resveratrol were mainly concentrated on the antioxidation, anti-inflammation, ameliorating mitochondrial dysfunction, and motor function. We discussed the disadvantages of different PD animal models, and we used meta-analysis approach to evaluate the results of the selected studies and used SYRCLE’s risk of bias tool to evaluate the methodological quality. Our analytical approach minimized the bias of different studies. We have also summarized the pharmacological mechanisms of resveratrol on PD models as reported by the researchers. The results of this study support the notion that resveratrol has significant neuroprotective effects on different PD models quantified using qualitative and quantitative methods. The collective information in our review can guide researchers to further plan their future experiments without any hassle regarding preclinical and clinical studies. In addition, this collective assessment of animal studies can provide a qualitative analysis of different PD animal models, either to guide further testing of these models or to avoid unnecessary duplication in their future research.

Perfluorooctanesulfonic acid (PFOS) is an emerging environmental organic pollutant that has been widely used in daily life products in the last century. Numerous studies showed that the accumulation of PFOS in human through food chain would lead to various disease. However, there is currently no report about its in situ localization in the tissue. In present study, we aimed to develop a reproductive and less-cost method to quantitatively detect and determine the spatial distribution of PFOS in mouse kidney by matrix-assisted laser desorption/ionization imaging mass spectrometry (MALDI-IMS) with a commercially available matrix. α-Cyano-4-hydroxycinnamic acid (CHCA) matrix was optimized for PFOS detection in MALDI-IMS analysis. Compared to other organic matrices, CHCA used in negative ion mode showed less background interference and enhanced MS signal intensity and high spatial resolution (80 μm) for PFOS analysis. The use of a CHCA matrix with an autospray system led to successful identification of the PFOS ion signals on the perfusion kidney tissue. The detection limit was at the μg/mL level, with direct visualization from a MS image. The developed method with the optimized parameters was successfully employed to obtain the PFOS spatial distribution in the kidney collected from mice after the PFOS exposure for 14 days. PFOS was mainly distributed in the kidney cortex region, which was consistent with the histological analysis results. Taken together, a rapid, economic, and efficient method was developed for PFOS detection by MALDI-IMS using a CHCA matrix. Mapping the distribution of PFOS by MALDI-IMS with a CHCA matrix provides an innovative approach for the analysis of environmental pollutants in animal or human tissues.

This study was designed to assess the use of a 3D printing technique in total hip arthroplasty (THA) for severe hip deformities, where new and improved approaches are needed. THAs were performed from January 2015 to December 2016. Bioprosthesis artificial hip joints were used in both conventional and 3D printing hip arthroplasties. A total of 74 patients (57 cases undergoing conventional hip replacements and 17 undergoing 3D printing hip replacements) were followed-up for an average of 24 months. The average age of the patients was 62.7 years. Clinical data between the patients treated with different approaches were compared. Results showed that the time to postoperative weight bearing and the Harris scores of the patients in the 3D printing group were better than those for patients in the conventional hip replacement group. Unfortunately, the postoperative infection and loosening rates were higher in the 3D printing group. However, there were no significant differences in femoral neck anteversion, neck shaft, acetabular or sharp angles between ipsilateral and contralateral sides in the 3D printing group (P>0.05). The femoral neck anteversion angle was significantly different between the two sides in the conventional hip replacement group (P<0.05). Based on these results, we suggest that the 3D printing approach provides a better short-term curative effect that is more consistent with the physiological structure and anatomical characteristics of the patient, and we anticipate that its use will help improve the lives of many patients.

No abstract