The performance of photovoltaic (PV) arrays are affected by the operating temperature, which is influenced by thermal losses to the ambient environment. The factors affecting thermal losses include wind speed, wind direction, and ambient temperature. The purpose of this work is to analyze how the aforementioned factors affect array efficiency, temperature, and heat transfer coefficient/thermal loss factor. Data on ambient and array temperatures, wind speed and direction, solar irradiance, and electrical output were collected from a PV array mounted on a CanmetENERGY facility in Varennes, Canada, and analyzed. The results were compared with computational fluid dynamics (CFD) simulations and existing results from PVsyst. The findings can be summarized into three points. First, ambient temperature and wind speed are important factors in determining PV performance, while wind direction seems to play a minor role. Second, CFD simulations found that temperature variation on the PV array surface is greater at lower wind speeds, and decreases at higher wind speeds. Lastly, an empirical correlation of heat transfer coefficient/thermal loss factor has been developed.

Electrical performance of photovoltaic (PV) cells are affected by their operating temperatures, which lead to changes in the performance of the PV panel. The performance and efficiency of a PV system is dependent upon many factors, such as its angle of incidence, accumulation of dust, speed and direction of natural winds. Particularly, angle of incidence between solar rays and PV modules is the most important. This paper will focus on developing a numerical tool for predicting the optimal tilt angle, based on wind flow over PV panel in a fixed tilt array, in order to observe the effects on performance. A 1.651 m long by 0.991 m wide solar PV panel is used in the analysis. The panel is mounted on top of a tall building and the tilt angle is fixed at one angle. This paper will observe how the PV panel is affected by wind flow and how the optimal tilt angle will change, and if it is necessary to account for convection. Increasing convective heat transfer has the potential to reduce the operating temperatures of photovoltaic solar panels thus increasing their efficiency and producing more power. This relationship was used in a numerical tool to predict the performance of the panel at different tilt angles and different wind speeds. The results show that wind speed and direction do affect power output and that designers should account for convective effects when designing positioning and orientation of solar panels.

The growing global interest in sustainable energy has paved the way to the rapid development of large-scale wind farms, consisting of dozens to hundreds of wind turbines. Although these large wind farms can generate enormous amount of power, they are also costly and require large areas of land or water, and thus are not suitable for urban environments. Smaller urban wind turbines have been developed for urban environments, but there are significant challenges to their widespread deployment. One of these challenges are their urban wind flows as they are strongly affected by complex building structures, producing highly turbulent flows. Any urban wind turbine would need to be designed to function efficiently and safely under these flow conditions; however, these unpredictable and turbulent winds can induce undesirable vibrations and cause early failures. Recently, bladeless wind turbines are gaining interest due to their reduced costs compared with conventional wind turbines such as the vertical-axis wind turbine and horizontal-axis wind turbine. These bladeless turbines convert flow wind energy into vibration energy, then converts the vibration energy into electricity. This paper examines the effects of force-induced vibrations on a cantilever beam system through wind tunnel experimentation. When fluid flows around a bluff body, periodic shedding of vortices may occur under the right conditions. The vortex shedding process creates an asymmetric pressure distribution on the body which causes the body to oscillate, known as vortex-induced vibrations. The purpose of the paper is to understand the factors affecting flowinduced vibrations and to improve wind energy harvesting from these vibrations. The first part of the paper focuses on wind tunnel experiments, by utilizing a cantilever beam configuration, conceptualized by previous research. Then, the experimental model was tested in different configurations, to determine the best setup for maximizing vibrations induced on the model. The long-term goal of the project was utilizing the model to optimize the system to improve efficiency of wind energy harvesting. The experimental results showed that the presence of an upstream cylinder will significantly improve the amplitude of vibration for energy harvesting, furthermore, the experiments showed that spacing in different directions also affect the amplitude of the vibrations. A two tandem cylinder system was used in this work, including a fixed rigid upstream cylinder and a downstream cylinder supported by a cantilever beam. Various configurations of these two cylinders in terms of spanwise and streamwise separation distances were studied and their maximum and root mean square displacements are reported for different wind speeds. Results showed that the presence of an upstream cylinder will significantly improve the amplitude of vibrations. This work verified that a wind energy harvester needs to consider the effects of wind speed and separation configuration of the cylinders in order to maximize the harvester's perfor...

No abstract