Er:YAG laser treatment of the zirconia surface did not result in a durable resin cement/ceramic bond; however, a durable bond between a conventional dual-cured resin cement and Procera All Ceram and Procera All Zirkon was formed using a ceramic primer containing the phosphate monomer, MDP, without any additional surface treatment.

There has been increasing interest on the development of clinically acceptable, more sensitive and specific methods for non-invasive diagnosis in Periodontics. In this pilot study, the performance of an Optical Coherence Tomography (OCT) system in imaging periodontal structures in humans was evaluated. Gingival sulcus depth measurements were obtained and compared with traditional probes. In total, 445 sites of 23 periodontally healthy individuals were measured by 3 instruments: North Carolina manual probe, Florida automated probe and OCT at 1325 nm. To obtain quantitative measurements from OCT images, the gingival refractive index was also determined. Discomfort/pain perception and the duration of examinations were compared among the instruments. The analysis of OCT images allowed the identification of relevant anatomic dental and periodontal regions. The average sulcus depth measured by OCT, 0.85 ± 0.27 mm and 0.87 ± 0.28 mm, was lower than the values obtained by manual and automated probing. Discomfort/pain were prevalent for traditional probes, which are invasive methods, than for the non-invasive OCT technique. OCT has the potential to be a reliable tool for in vivo periodontal tissues evaluation and for reproducible sulcus depth measurements in healthy sites. Further technological advances are required to reduce the procedure time and promote evaluation of posterior oral regions. Photonic assessment of periodontal tissue with OCT (top) in a clinical environment, showing tooth/gingiva features (bottom).

No abstract

Evaluation of molar dental restorations on enamel is performed using optical coherence tomography (OCT) with 10 microm resolution. Images of approximately 50 microm failure gaps in the restorations are demonstrated and the OCT images are compared with x-ray and optical microscopy pictures. The results demonstrate the potential of the technique for clinical evaluation of dental restorations.

No abstract

No abstract

A flexible organic random laser based on poly(9,9-dioctylfluorene) deposited on a surface corrugated polyphthalate-carbonate substrate Appl. Phys. Lett. 98, 253304 (2011) We demonstrate random lasing action in flexible bacterial cellulose (BC) membrane containing a laser-dye and either dielectric or metallic nanoparticles (NPs). The novel random laser system consists of BC nanofibers attached with Rhodamine 6G molecules and having incorporated either silica or silver NPs. The laser action was obtained by excitation of the samples with a 6 ns pulsed laser at 532 nm. Minimum laser threshold of %0.7 mJ/pulse was measured for the samples with silica NPs, whereas a laser threshold of 2.5 mJ/pulse for a system based on silver NPs was obtained. In both cases a linewidth narrowing from %50 to %4 nm was observed. Potential applications in biophotonics and life sciences are discussed for this proof-of-concept device. V C 2014 AIP Publishing LLC. [http://dx

SUMMARYThis study evaluated the long-term durability of three one-step adhesive-composite systems to ground enamel and dentin. Twenty-seven teeth were randomly divided into three groups of nine. The first group had its crowns sectioned to expose superficial dentin, which was then ground with 600 grit SiC paper. One of three onestep adhesives: a trial bonding agent, OBF-2; i Bond or Adper Prompt L-Pop was applied to the dentin of three teeth and built-up with the corresponding resin composite (Estelite Σ, Venus or Filtek Supreme). The second group of nine teeth had their enamel approximal surfaces ground with wet 600-grit SiC paper, then one of the three one-step adhesives was applied and built-up with resin composite. The bonded specimens were sliced into 0.7 mm-thick slabs. After 24 hours and one year of water storage at 37°C, the slabs were sectioned into beams for the microtensile bond strength test. Failure modes were observed using optical and electron scanning microscopy. The third group of nine teeth had approximal wedgeshaped cavities prepared above the CEJ intoResin-enamel and resin-dentin bonds formed by one-step adhesive-composite systems from the same manufacturer were not hydrolytically stable after accelerated aging in water. Operative Dentistry dentin. Two-to-three grains of rhodamine B were added to each of the three adhesives prior to restoring the cavities with resin composite. After 24 hours storage, the teeth were sectioned and their interfaces examined with a laser scanning confocal microscope. The bond strengths of the three adhesive-composite systems to both enamel and dentin significantly lessened after one year of water storage, however, there was no significant difference between the materials.