Introduction:One of the most frequently used method for scanning patients with indication for dental implantation in dentistry is cone beam computed tomography. Implantation, CBCT imaging and implant programme are inevitable when planning a successful replacement of lost teeth. CBCT offers exact information about available bone and its density, adjacent tooth roots, the place of mandibular canal and maxillary sinus and adjacent anatomical structure.Aim:The goal of this study is to estimate accuracy of measurements on CBCT images ofpatients who have implants of different producers and determine if there is any statistically significant correlation between four test groups regardless of the alloy of which implants are made.Material and methods:The study was a prospective-comparative, and included fifteen patients with hundred dental implants divided in four groups depending on the producer.Results:Over dimensioning in the gained measurements of the whole sample on CBCT images in relation to dimensions of producers is between 0.1006mm and 0.368mm. Even though over dimensioning is measured in millimetres, it has to be taken into consideration in clinical practice when planning an implant placement, and we can recommend safety zone of 0.5mm. There have been no statistically significant differences in the gained results in over dimensioning of implants of different alloys for horizontal and vertical measurements on CBCT images of Astra Tech, Brendet titanium implants and Straumann titanium-zirconium implants. Based on the goals of the study there have been confirmed statistically significant correlations of great value (from 0.841 to 0.936) of high level of importance between manufactured value of dimensions and average dimensions values gained through CBCT imaging in four types of implants (four test groups). The total exactness of measurements on CBCT scan in this research is 96.66% for horizontal measuring and 96.92% for vertical measuring. Therefore, we can conclude that CBCT as radiological method has an unavoidable importance in planning and successful realisation of dental implant procedure.Conclusion:Cone Beam Computed Tomography provides exact measurements of dimensions of placed dental implant in relation to dimensions of the producers of the implant because the material from which dental implants have been made does not significantly affect the precision of the measurement.
<div class="WordSection1"><p><strong>Objective. </strong>To evaluate and compare the water sorption of three luting cements in three different solutions: distilled water and artificial saliva with different pH values (7.4 and 3.0). <strong>Materials and methods</strong>. Resin-modified glass-ionomer cement (GC Fuji Plus) and two resin cements (Multilink Automix and Variolink II) were used. A total of 45 specimens - 15 specimens (15x1 mm) for each cement were prepared according to ISO standard 4049:2009. The water sorptions of the cements were calculated by weighing the specimens before and after immersion and desiccation. <strong>Results. </strong>Nonparametric statistic methods were applied. GC Fuji Plus cement showed significantly higher values of water sorption in all three solutions of both resin cements (p<0.009) and significantly higher values of sorption in artificial saliva pH 3.0. Multilink Automix showed significantly higher values of water sorption compared with Variolink II in artificial saliva pH 7.4, and higher values of sorption in this solution compared with pH value 3.0. <strong>Con- clusion. </strong>Water sorption values are mainly influenced by the proportion of hydrophilic matrix, the type and composition of filler, and the pH value of solutions.</p></div>
<p><strong>Objective.</strong> To evaluate the influence of gender on the mental index (MI) and the mandibular cortical index (MCI).</p><p><strong>Methods.</strong> In this study, there were 120 subjects (43 male and 77 female subjects), who had undergone a dental panoramic radiograph examination for the needs of diagnosis and future treatment planning. MI and MCI were determined by orthopantomograph.</p><p><strong>Results.</strong> There was a statistically significant difference in MI dependent on gender. Male patients demonstrated significantly higher values for MI than female patients (right: t=4.127; P=0.0001, left: t=3.110; P=0.002). No statistically significant difference was observed for MCI dependent on gender (right: χ²=2.36 P=0.308, left: χ²=3.85 P=0.146).</p><p><strong>Conclusion. </strong>MI is affected by gender, but MCI is not.</p>
Objectives The aim of the study was to analyze the occurrence of stress on teeth with abfraction lesions restored with six different restorative materials, and by introducing the tensile strength parameters to calculate the safety factor of the material under the load (ratio between the strength of the material and the maximum stress). Materials and Methods Three-dimensional models of the mandibular premolar are created from a microcomputed tomography images. An abfraction lesion is modeled on the tooth. The stress of the dental tissues and six restorative materials under functional and nonfunctional occlusal loading of 200 (N) are analyzed by finite element method. Statistical Analysis CTAn program 1.10 and ANSYS Workbench (version 14.0) were used for analysis. Results are presented in von Mises stress. Results Oblique loads caused ≈ four times higher stress in restorative materials than the axial ones. It is noticeable that high values of von Mises stress are measured at the bottom of the sharp lesion, even up to 240 MPa, that are significantly reduced after the restoration. The highest stresses at the restorative material are present at the lower (gingival) margin of the restoration. The highest stresses under both types of loads are measured in nanohybrid composite (Tetric EvoCeram, Ivoclar Vivadent). The lowest values of the stress are measured in the flowable composite (Tetric Flow, Ivoclar Vivadent), but at the same time, the highest value of the stress is measured in the surrounding dental tissues on the tooth restored with the flowable composite. The microhybrid composite (Herculite XR, Kerr), with the highest safety factor, is the material that best withstands the stresses it is exposed to. The obtained safety factor did not exceed the critical limit, except for the glass ionomer cement, with the safety factor lower than 1. Conclusion The type of tooth loading has the greatest influence on the intensity of stress. The value of the obtained stresses in the restorative material and dental tissues differ due to the different mechanical properties of the materials. Restoration of noncarious lesions significantly reduces extremely high stress values at their bottom.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.