Recently, carbon nanotubes (CNTs) have been used extensively to develop new materials and devices due to their specific morphology and properties. The reinforcement of different metal oxides such as zinc oxide (ZnO) with CNT develops advanced multifunctional materials with improved properties. Our aim is to obtain ZnO-CNT nanocomposites by in situ hydrothermal method in high-pressure conditions. Various compositions were tested. The structure and morphology of ZnO-CNT nanocomposites were analyzed by Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry—thermogravimetry (DSC-TG), X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), and transmission electron microscopy (TEM). These analyses showed the formation of complex ZnO-CNT structures. FT-IR spectra suggest possible interactions between CNT and ZnO. DSC-TG analysis also reveals the formation of some physical bonds between ZnO and CNT, through the appearance of endothermic peaks which could be assigned to the decomposition of functional groups of the CNT chain and breaking of the ZnO-CNT bonds. XRD characterization demonstrated the existence of ZnO nanocrystallites with size around 60 nm. The best ZnO:CNT composition was further selected for preliminary investigations of the potential of these nanocomposite powders to be processed as pastes for extrusion-based 3D printing.
During the microwave sintering of a polymer-ceramic composite plasma discharge is experienced. The discharge could occur failure of the power source. The solution proposed by the paper is original, no similar solutions being presented by the literature. It consists of using a polymer-ceramic composite protective panel, to stop the plasma discharge to the entrance of the guiding tunnel. Six composites resulted by combining three polymers, Polytetrafluoroethylene (PTFE), STRATITEX composite and Polyvinylchloride (PVC) with two natural ceramics containing calcium carbonate: Rapana Thomasiana (RT) sea-shells and beach sand were used to build the protective panel.Theoretical balance of the power to the panel was analysed and the thermal field was determined. It was applied heating using 0.6-1.2-1.8-2.4-3.0 kW microwave beam power. The panels were subjected to heating with and without material to be sintered. It was analyzed: RT chemical (CaCO3 as Calcite and Aragonite), burned area (range: 200–4000 mm2) and penetration (range: 1.6–5.5 mm), and thermal analysis of the burned areas comparing to the original data. PTFE-RT composite proved the lowest penetration to 0.6 and 1.2 kW. Other 1.2 kW all composites experienced vital failures. Transformation of the polymer matrix of composite consisted of slightly decreasing of the phase shifting temperature and of slightly increasing of the melting start and liquidus temperature.
Magnetic iron oxide particles are used for in vitro diagnostics for nearly 40 years. Due to their unique physical, chemical, thermal and mechanical properties, as well as biocompatibility and low toxicity in the human body, iron oxide nanoparticles have been used in many biomedical applications, such as contrast agents for magnetic resonance imaging, carriers for controlled drug delivery and immunoassays, but also in magnetic hyperthermia. Our aim is to investigate the effect of pressure and temperature on the structural, thermal and magnetic properties of iron oxide nanomaterials prepared by hydrothermal synthesis. Iron oxide nanoparticles were synthesized at temperatures of 100-200°C and pressures of 20-1000 bar. It has been found that pressure influences the type of iron oxide crystalline phase. Thus, for lower pressure values (< 100 bar), iron oxide is predominantly formed as hematite, while at pressures > 100 bar, the major crystalline phase is goethite. The complex thermal analysis revealed the polymorphic changes of iron oxides at different temperatures. The existence of specific magnetite and hematite phases in all thermally treated samples are evidenced through the specific Verwey and Morin transitions highlighted by ZFC-FC (Zero Field Cooled-Field Cooled) measurements, whereas their relative content is precisely provided by Mössbauer spectroscopy.
Heavy metals have a major contribution to biosphere pollution due to toxicity. The detection and monitoring of the environmental agents in soil, water and air is very important for the general health of humans and animals. It has been recently shown that electrochemical techniques such as differential pulse voltammetry (DPV) and square wave anodic stripping voltammetry (SWASV) using modified electrodes are very attractive methods for detecting heavy metals. The aim of this paper is to demonstrate the potential of hydrothermal process combined with electrochemical techniques to obtain modified electrodes based on functionalized carbon nanotubes (CNTs) and polyaniline (PANI) for metals detection. Commercial multi-walled carbon nanotubes (MWCNT) were functionalized by a mixture of HNO3/H2SO4 and further used for hydrothermal synthesis of CNT-PANI composites with different mass ratios. The resulted powders were analyzed by spectral (Fourier-Transform Infrared Spectroscopy) and thermal (Differential Scanning Calorimetry) methods, and then dispersed in a surfactant/electrolyte solution for preliminary electrochemical experiments (cyclic voltammetry, CV and DPV) to obtain modified electrodes. The influence of the CNT: PANI mass ratio and the synthesis time on the formation of composites with the desired structural and electrochemical properties were studied. It was found that CNT-PANI composite powder having mass ratio 1:4 and synthesis time 3h has the best structural and thermal characteristics and formed a weakly conductive film on the surface of the glassy carbon electrode. Preliminary electrochemical tests revealed the electroactive forms of polyaniline, through the presence of characteristic oxidation peaks but also reduction peaks, corresponding to reversible redox reactions, demonstrating that glassy carbon electrode has been electrochemically modified with CNT-PANI coatings. Further studies will be conducted to test the potential application of glassy carbon electrode modified with CNT-PANI coatings as electrochemical sensor for heavy metals detection.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.