Directing efficient hole transport Surface defects in three-dimensional perovskites can decrease performance but can be healed with coatings based on two-dimensional (2D) perovskite such as Ruddlesden-Popper phases. However, the bulky organic groups of these 2D phases can lead to low and anisotropic charge transport. F. Zhang et al . show that a metastable polymorph of a Dion-Jacobson 2D structure based on asymmetric organic molecules reduced the energy barrier for hole transport and their transport through the layer. When used as a top layer for a triple-cation mixed-halide perovskite, a solar cell retained 90% of its initial power conversion efficiency of 24.7% after 1000 hours of operation at approximately 40°C in nitrogen. —PDS

Although the power conversion efficiency of perovskite solar cells has increased from 3.81% to 22.1% in just 7 years, they still suffer from stability issues, as they degrade upon exposure to moisture, UV light, heat, and bias voltage. We herein examined the degradation of perovskite solar cells in the presence of UV light alone. The cells were exposed to 365 nm UV light for over 1,000 h under inert gas at <0.5 ppm humidity without encapsulation. 1-sun illumination after UV degradation resulted in recovery of the fill factor and power conversion efficiency. Furthermore, during exposure to consecutive UV light, the diminished short circuit current density (Jsc) and EQE continuously restored. 1-sun light soaking induced recovery is considered to be caused by resolving of stacked charges and defect state neutralization. The Jsc and EQE bounce-back phenomenon is attributed to the beneficial effects of PbI2 which is generated by the decomposition of perovskite material.

Halide perovskites with bandgaps of 1.70–1.85 eV are of interest for multijunction photovoltaics. Mixing halides on the X site of the ABX3-structured perovskite system is a common way to reach these bandgaps, but this method introduces phase segregation pathways, limiting photovoltage. Recently, a new strategy for increasing the bandgap has been introduced, where cations normally too large to fit into the lattice, but compensated by smaller cations, are substituted on the A site. The mechanism underlying the increase of the bandgap with this strategy remained an open question. Here, we show that by partial substitution of the large dimethylammonium (DMA) cation at the A site of FA x Cs1–x PbI y Br3–y perovskites, a bandgap increase is observed not only when DMA is compensated by smaller Cs cations but also when only DMA is added, which is accompanied by an expansion of the crystal lattice. Our experimental findings suggest that adding DMA is causing an unexpected tilt in the perovskite octahedra, increasing the bandgap. Efficient solar cells based on 1.73 eV DMA-incorporated materials are extremely stable, retaining 96% of their original efficiency over 2200 h at 85 °C in the dark and 92% of their original efficiency after operation at 60 °C for 500 h. This octahedral tilting strategy is a promising route for attaining efficient and stable wide bandgap perovskite solar cells.

Mixed tin–lead halide perovskite solar cells have promising power conversion efficiencies, but long-term stability is still a challenge. Herein we examine the stability of a 60:40 tin–lead perovskite to better understand diminished device performance upon thermal treatment, both in ambient and inert atmosphere. Operando X-ray diffraction shows a stable bulk structure of the perovskite absorber, leading to the hypothesis that surface chemistry dominates the degradation mechanism. X-ray photoelectron spectroscopy reveals two new observations post-thermal annealing that accompany previously reported Sn4+ evolution: (i) the formation of I3 – intermediates preceding I2 loss at the surface and (ii) evidence of under-coordinated tin and lead surface sites (Snδ<2+ and Pbδ<2+, respectively) in inert and ambient conditions. These two species indicate an activated corrosion (i.e., both oxidation and reduction) process at the surface as a possible chemical pathway for degradation, which is expected to be accelerated under operando voltage and light biases.