Continental breakup occurs through repeated episodes of mechanical stretching and dike injection within discrete, narrow rift segments. However, the time and length scales of the dike intrusions, along with the source regions of melt within continental and oceanic rifts, are poorly constrained. We present measurements of spatial and temporal variability in deformation from the currently active 60-km-long Dabbahu segment of the Red Sea rift in Afar, using satellite radar, global positioning system, and seismicity data sets, that capture emplacement of two ~10-km-long, ~1-2-m-wide dike intrusions in June and July 2006. Our observations show that the majority of strain is accommodated by dikes that propagate laterally over ~4-5 h time scales along the rift axis and are sourced from a reservoir in the middle to lower crust, or upper mantle, beneath the center of the rift segment. New intrusions during the ongoing rifting episode in Afar show that the injection of lateral dikes fed from magma reservoirs beneath rift segment centers is a key component in creating and maintaining regular along-axis rift segmentation during the fi nal stages of continental breakup. Our observations also provide evidence that the focused magmatic accretion at segment centers observed in slow-spreading mid-ocean ridges occurs prior to the onset of seafl oor spreading.

SUMMARY A 60‐km‐long dyke intruded the Dabbahu segment of the Nubia–Arabia Plate boundary (Afar, Ethiopia) in 2005 September, marking the beginning of an ongoing rifting episode. We have monitored the continuing activity using Satellite Radar Interferometry (InSAR) and with data from Global Positioning System (GPS) instruments and seismometers deployed around the rift in response to the initial intrusion. These data show that a sequence of new dyke intrusions has reintruded the central and southern section of the Dabbahu segment. The first was in 2006 June and seven new dykes were emplaced by the end of 2007. Modelling of InSAR data indicates that the dykes were between 0.5 and 2 m wide, up to ∼10 km long and confined to the upper 10 km of crust. An intrusion in 2007 August was associated with a 5‐km‐long basaltic fissural eruption. During the new dyke injections, InSAR and GPS data show no subsidence at either of the volcanoes at the northern end of the segment, which partly fed the 2005 September dyke. Seismicity data imply that the dykes were probably fed from a source near the Ado'Ale Silicic Complex at the centre of the segment, but the lack of significant subsidence there implies that the source is very deep, or that there was minimal deflation at shallow magma sources. The new dykes are concentrated in an area where the 2005 dyke did not produce significant opening, implying that residual tensile tectonic stresses are higher in this location and are focusing the later intrusions. The sequence of dyke intrusions observed so far is similar to those seen in Iceland during the Krafla rifting episode, which lasted 9 yr from 1975 to 1984. It is likely that, with a continued magma supply, dykes will continue to be intruded until the tectonic stress is fully relieved. As observed at Krafla, eruptions are likely to become more common before the rifting episode is concluded.

[1] La Fossa cone is an active stratovolcano located on Vulcano Island in the Aeolian Archipelago (southern Italy). Its activity is characterized by explosive phreatic and phreatomagmatic eruptions producing wet and dry pyroclastic surges, pumice fall deposits, and highly viscous lava flows. Nine 2-D electrical resistivity tomograms (ERTs; electrode spacing 20 m, with a depth of investigation >200 m) were obtained to image the edifice. In addition, we also measured the self-potential, the CO 2 flux from the soil, and the temperature along these profiles at the same locations. These data provide complementary information to interpret the ERT profiles. The ERT profiles allow us to identify the main structural boundaries (and their associated fluid circulations) defining the shallow architecture of the Fossa cone. The hydrothermal system is identified by very low values of the electrical resistivity (<20 W m). Its lateral extension is clearly limited by the crater boundaries, which are relatively resistive (>400 W m). Inside the crater it is possible to follow the plumbing system of the main fumarolic areas. On the flank of the edifice a thick layer of tuff is also marked by very low resistivity values (in the range 1-20 W m) because of its composition in clays and zeolites. The ashes and pyroclastic materials ejected during the nineteenth-century eruptions and partially covering the flank of the volcano correspond to relatively resistive materials (several hundreds to several thousands W m). We carried out laboratory measurements of the electrical resistivity and the streaming potential coupling coefficient of the main materials forming the volcanic edifice. A 2-D simulation of the groundwater flow is performed over the edifice using a commercial finite element code. Input parameters are the topography, the ERT cross section, and the value of the measured streaming current coupling coefficient. From this simulation we computed the self-potential field, and we found good agreement with the measured self-potential data by adjusting the boundary conditions for the flux of water. Inverse modeling shows that self-potential data can be used to determine the pattern of groundwater flow and potentially to assess water budget at the scale of the volcanic edifice. Citation: Revil, A., et al. (2008), Inner structure of La Fossa di Vulcano (Vulcano Island, southern Tyrrhenian Sea, Italy) revealed by high-resolution electric resistivity tomography coupled with self-potential, temperature, and CO 2 diffuse degassing measurements,