A volume and a twin surface dielectric barrier discharge (VDBD and SDBD) are generated in different nitrogen-oxygen mixtures at atmospheric pressure by applying damped sinusoidal voltage waveforms with oscillation periods in the microsecond time scale. Both electrode configurations are located inside vacuum vessels and operated in a controlled atmosphere to exclude the influence of surrounding air. The discharges are characterised with different spatial and temporal resolution by applying absolutely calibrated optical emission spectroscopy in conjunction with numerical simulations and current-voltage measurements. Plasma parameters, namely the electron density and the reduced electric field, and the dissipated power are found to depend strongly on the oxygen content in the working gas mixture. Different spatial and temporal distributions of plasma parameters and dissipated power are explained by surface and residual volume charges for different O 2 admixtures due to their effects on the electron recombination rate. Thus, the oxygen admixture is found to strongly influence the breakdown process and plasma conditions of a VDBD and a SDBD. K E Y W O R D S collisional-radiative model, controlled atmosphere, dielectric barrier discharge, optical emission spectroscopy, plasma parameters ---

A voltage and power controlled surface dielectric barrier discharge for the removal of volatile organic compounds (VOCs) from gas streams is studied by means of current–voltage measurements, flame ionization detectors, and gas chromatography–mass spectrometry (GC–MS). The discharge is generated in a defined synthetic air gas stream at atmospheric pressure by application of a damped sinusoidal voltage waveform resulting from a resonant circuit. Multiple organic compounds, namely n-butane, butanol, isobutanol, ethyl acetate, diethyl ether, and butoxyethanol, are tested at concentrations of 50, 100, 200, and 400 ppm (parts per million), as well as peak-to-peak voltages of 8 to 13 kVpp and pulse repetition frequencies of 250 to 4000 Hz. The dissipated power within the system is calculated utilizing the measured voltage and current waveforms. The conversion and absolute degradation of the VOCs are determined by flame ionization detectors. An increasing concentration of VOCs is found to increase the dissipated power marginally, suggesting a higher conductivity and higher electron densities in the plasma. Of the applied VOCs, n-butane is found to be the most resistant to the plasma treatment, while higher concentrations consistently result in a lower conversion and a higher absolute degradation across all tested compounds. Corresponding amounts of converted molecules per expended joule are given as a comparable parameter by weighting the absolute degradation with the dissipated power. Finally, specific reaction products are determined by online GC–MS, further confirming carbon dioxide (CO2) as a major reaction product, alongside a variety of less prevalent side products, depending on the structure of the original compound. The findings of this study are intended to promote the development of energy efficient processes for the purification of gas streams in both, industry and consumer market. Potential applications of the presented technique could be found in car paint shops, chemical plants, hospital ventilation systems, or air purifiers for living space.

The effect of the selection of hexamethyldisiloxane (HMDSO) and hexamethyldisilazane (HMDSN) as a precursor in a microwave driven low pressure plasma on the deposition of silicon oxide barrier coatings and silicon based organic interlayers on polyethylene terephthalate (PET) and polypropylene (PP) substrates is investigated. Mass spectrometry is used to quantify the absolute gas density and the degree of depletion of neutral precursor molecules under variation of oxygen admixture. On average, HMDSN shows a smaller density, a higher depletion and the production of smaller fragments. Subsequently, this is correlated with barrier performance and chemical structure as a function of barrier layer thickness and oxygen admixture on PET. For this purpose, the oxygen transmission rate (OTR) is measured and Fourier transformed infrared (FTIR) spectroscopy as well as x-ray photoelectron spectroscopy (XPS) is performed. HMDSN based coatings exhibit significantly higher barrier performances for high admixtures of oxygen (200 sccm). In comparison to HMDSO based processes, however, a higher supply of oxygen is necessary to achieve a sufficient degree of oxidation, cross-linking and, therefore, barrier performance. FTIR and XPS reveal a distinct carbon content for low oxygen admixtures (10 and 20 sccm) in case of HMDSN based coatings. The variation of interlayer thickness also reveals significantly higher OTR for HMDSO based coatings on PET and PP. Barrier performance of HMDSO based coatings improves with increasing interlayer thickness up to 10 nm for PET and PP. HMDSN based coatings exhibit a minimum of OTR without interlayer on PP and for 2 nm interlayer thickness on PET. Furthermore, HMDSN based coatings show distinctly higher bond strengths to the PP substrate.

A twin surface dielectric barrier discharge is used for the catalyst‐enhanced plasma oxidation of 300 ppm n‐butane in synthetic air. Plasma‐only operation results in the conversion of n‐butane into CO and CO2. Conversion is improved by increasing the temperature of the feed gas, but selectivity shifts to undesired CO. α‐MnO2 is used as a catalyst deposited on the electrodes by spray coating with a distance of 1.5 mm between the uncoated grid lines and the square catalyst patches to prevent the inhibition of plasma ignition. The catalyst strongly influences selectivity, reaching 40% conversion and 73% selectivity to CO2 at a specific energy density of 390 J·L−1 and 140°C, which is far below the onset temperature of thermocatalytic n‐butane conversion.

No abstract