Adhesion is a fundamental phenomenon with great importance in technology, in our everyday life, and in nature. In this article, we review physical interactions that resist the separation of two solids in contact. By using examples of biological attachment systems, we summarize and categorize various principles that contribute to the so-called gecko effect. Emphasis is placed on the contact geometry and in particular on the mushroom-shaped geometry, which is observed in long-term biological adhesive systems. Furthermore, we report on artificial model systems with this bio-inspired geometry and demonstrate that surface microstructures with this geometry are promising candidates for technical applications, in which repeatable, reversible, and residue-free adhesion under different environmental conditions—such as air, fluid, and vacuum—is required. Various applications in robotic systems and in industrial pick-and-place processes are discussed.

Nature has successfully evolved the mushroom-shaped contact geometry in many organisms in order to solve the attachment problem. We studied the detachment process of individual bioinspired artificial mushroom-shaped adhesive microstructures (MSAMSs) resolving the failure dynamics at high spatiotemporal resolution. The experimental data provide strong evidence for a homogeneous stress distribution in MSAMS, which was recently proposed. Our results allow us to explain the advantage of such contact geometry and provide a suggestion for the widely observed mushroom-shaped contact geometry.

Dragonflies count among the most skilful of the flying insects. Their exceptional aerodynamic performance has been the subject of various studies. Morphological and kinematic investigations have showed that dragonfly wings, though being rather stiff, are able to undergo passive deformation during flight, thereby improving the aerodynamic performance. Resilin, a rubber-like protein, has been suggested to be a key component in insect wing flexibility and deformation in response to aerodynamic loads, and has been reported in various arthropod locomotor systems. It has already been found in wing vein joints, connecting longitudinal veins to cross veins, and was shown to endow the dragonfly wing with chordwise flexibility, thereby most likely influencing the dragonfly's flight performance. The present study revealed that resilin is not only present in wing vein joints, but also in the internal cuticle layers of veins in wings of Sympetrum vulgatum (SV) and Matrona basilaris basilaris (MBB). Combined with other structural features of wing veins, such as number and thickness of cuticle layers, material composition, and cross-sectional shape, resilin most probably has an effect on the vein's material properties and the degree of elastic deformations. In order to elucidate the wing vein ultrastructure and the exact localisation of resilin in the internal layers of the vein cuticle, the approaches of bright-field light microscopy, wide-field fluorescence microscopy, confocal laser-scanning microscopy, scanning electron microscopy and transmission electron microscopy were combined. Wing veins were shown to consist of up to six different cuticle layers and a single row of underlying epidermal cells. In wing veins of MBB, the latter are densely packed with light-scattering spheres, previously shown to produce structural colours in the form of quasiordered arrays. Longitudinal and cross veins differ significantly in relative thickness of exo- and endocuticle, with cross veins showing a much thicker exocuticle. The presence of resilin in the unsclerotised endocuticle suggests its contribution to an increased energy storage and material flexibility, thus to the prevention of vein damage. This is especially important in the highly stressed longitudinal veins, which have much lower possibility to yield to applied loads with the aid of vein joints, as the cross veins do. These results may be relevant not only for biologists, but may also contribute to optimise the design of micro-air vehicles.

Tetrapodal ZnO crystals are used for mechanical interlocking of PTFE and cross-linked PDMS, classically non-adhesive polymers. This novel approach is straightforward and easily applicable and leads to a peel strength that is higher than 200 N m(-1) without chemical modification of the surfaces. The shape of these fillers emerged as a crucial aspect of the interlocking mechanism.

To shed light on the role of suction in adhesion of microstructure with mushroom-shaped terminal elements, we compared pull-off forces measured at different retraction velocities on structured and smooth surfaces under different pressure conditions. The results obtained allow us to suggest that suction may contribute up to 10 per cent of the pull-off force measured on the structured surfaces at high velocities. We therefore conclude that the attachment ability of this biomimetic adhesive must not be solely based on van der Waals forces. Our experiments also suggest a change in visco-elastic properties of the structured surfaces compared with the bulk material. Based on the results obtained, it is assumed that this adhesive may be suitable in dynamic pick-and-drop processes even under vacuum conditions at which sufficiently high adhesive capability is maintained.

SummaryThe aim of this study was to understand the influence of microstructures found on ventral scales of the biological model, Lampropeltis getula californiae, the California King Snake, on the friction behavior. For this purpose, we compared snake-inspired anisotropic microstructured surfaces to other microstructured surfaces with isotropic and anisotropic geometry. To exclude that the friction measurements were influenced by physico-chemical variations, all friction measurements were performed on the same epoxy polymer. For frictional measurements a microtribometer was used. Original data were processed by fast Fourier transformation (FFT) with a zero frequency related to the average friction and other peaks resulting from periodic stick-slip behavior. The data showed that the specific ventral surface ornamentation of snakes does not only reduce the frictional coefficient and generate anisotropic frictional properties, but also reduces stick-slip vibrations during sliding, which might be an adaptation to reduce wear. Based on this extensive comparative study of different microstructured polymer samples, it was experimentally demonstrated that the friction-induced stick-slip behavior does not solely depend on the frictional coefficient of the contact pair.

SummaryThe microstructure investigated in this study was inspired by the anisotropic microornamentation of scales from the ventral body side of the California King Snake (Lampropeltis getula californiae). Frictional properties of snake-inspired microstructured polymer surface (SIMPS) made of epoxy resin were characterised in contact with a smooth glass ball by a microtribometer in two perpendicular directions. The SIMPS exhibited a considerable frictional anisotropy: Frictional coefficients measured along the microstructure were about 33% lower than those measured in the opposite direction. Frictional coefficients were compared to those obtained on other types of surface microstructure: (i) smooth ones, (ii) rough ones, and (iii) ones with periodic groove-like microstructures of different dimensions. The results demonstrate the existence of a common pattern of interaction between two general effects that influence friction: (1) molecular interaction depending on real contact area and (2) the mechanical interlocking of both contacting surfaces. The strongest reduction of the frictional coefficient, compared to the smooth reference surface, was observed at a medium range of surface structure dimensions suggesting a trade-off between these two effects.

The louse fly is an obligate blood-sucking ectoparasite of the common swift As a result of reduction of the wings, is unable to fly; thus, an effective and reliable attachment to their host's plumage is of utmost importance. The attachment system of shows several modifications in comparison to that of other calyptrate flies, notably the large tridentate claws and the dichotomously shaped setae located on the pulvilli. Based on data from morphological analysis, confocal laser scanning microscopy, cryo-scanning electron microscopy and attachment force experiments performed on native (feathers) as well as artificial substrates (glass, epoxy resin and silicone rubber), we showed that the entire attachment system is highly adapted to the fly's lifestyle as an ectoparasite. The claws in particular are the main contributor to strong attachment to the host. Resulting attachment forces on feathers make it impossible to detach without damage to the feathers or to the legs of the louse fly itself. Well-developed pulvilli are responsible for the attachment to smooth surfaces. Both dichotomously shaped setae and high setal density explain high attachment forces observed on smooth substrates. For the first time, we demonstrate a material gradient within the setae, with soft, resilin-dominated apical tips and stiff, more sclerotized bases in Diptera. The empodium seems not to be directly involved in the attachment process, but it might operate as a cleaning device and may be essential to maintain the functionality of the entire attachment system.