In contrast to synthetic materials, materials produced by organisms are formed in ambient conditions and with a limited selection of elements. Nevertheless, living organisms reveal elegant strategies for achieving specific functions, ranging from skeletal support to mastication, from sensors and defensive tools to optical function. Using state-of-the-art characterization techniques, we present a biostrategy for strengthening and toughening the otherwise brittle calcite optical lenses found in the brittlestar This intriguing process uses coherent nanoprecipitates to induce compressive stresses on the host matrix, functionally resembling the Guinier-Preston zones known in classical metallurgy. We believe that these calcitic nanoparticles, being rich in magnesium, segregate during or just after transformation from amorphous to crystalline phase, similarly to segregation behavior from a supersaturated quenched alloy.

Female insects of diverse orders bore into substrates to deposit their eggs. Such insects must overcome several biomechanical challenges to successfully oviposit, which include the selection of suitable substrates through which the ovipositor can penetrate without itself fracturing. In many cases, the insect may also need to steer and manipulate the ovipositor within the substrate to deliver eggs at desired locations before rapidly retracting her ovipositor to avoid predation. In the case of female parasitoid ichneumonid wasps, this process is repeated multiple times during her lifetime, thus testing the ability of the ovipositioning apparatus to endure fracture and fatigue. What specific adaptations does the ovipositioning apparatus of a female ichneumonoid wasp possess to withstand these challenges? We addressed this question using a model system composed of parasitoid and pollinator fig wasps. First, we show that parasitoid ovipositor tips have teeth-like structures, preferentially enriched with zinc, unlike the smooth morphology of pollinator ovipositors. We describe sensillae present on the parasitoid ovipositor tip that are likely to aid in the detection of chemical species and mechanical deformations and sample microenvironments within the substrate. Second, using atomic force microscopy, we show that parasitoid tip regions have a higher modulus compared with regions proximal to the abdomen in parasitoid and pollinator ovipositors. Finally, we use videography to film wasps during substrate boring and analyse buckling of the ovipositor to estimate the forces required for substrate boring. Together, these results allow us to describe the biomechanical principles underlying substrate boring in parasitoid ichneumonid wasps. Such studies may be useful for the biomimetic design of surgical tools and in the use of novel mechanisms to bore through hard substrates.

BackgroundResource partitioning is facilitated by adaptations along niche dimensions that range from morphology to behaviour. The exploitation of hidden resources may require specially adapted morphological or sensory tools for resource location and utilisation. Differences in tool diversity and complexity can determine not only how many species can utilize these hidden resources but also how they do so.Methodology and Principal FindingsThe sclerotisation, gross morphology and ultrastructure of the ovipositors of a seven-member community of parasitic wasps comprising of gallers and parasitoids developing within the globular syconia (closed inflorescences) of Ficus racemosa (Moraceae) was investigated. These wasps also differ in their parasitism mode (external versus internal oviposition) and their timing of oviposition into the expanding syconium during its development. The number and diversity of sensilla, as well as ovipositor teeth, increased from internally ovipositing to externally ovipositing species and from gallers to parasitoids. The extent of sclerotisation of the ovipositor tip matched the force required to penetrate the syconium at the time of oviposition of each species. The internally ovipositing pollinator had only one type of sensillum and a single notch on the ovipositor tip. Externally ovipositing species had multiple sensilla types and teeth on their ovipositors. Chemosensilla were most concentrated at ovipositor tips while mechanoreceptors were more widely distributed, facilitating the precise location of hidden hosts in these wasps which lack larval host-seeking behaviour. Ovipositor traits of one parasitoid differed from those of its syntopic galler congeners and clustered with those of parasitoids within a different wasp subfamily. Thus ovipositor tools can show lability based on adaptive necessity, and are not constrained by phylogeny.Conclusions/SignificanceOvipositor structure mirrored the increasingly complex trophic ecology and requirements for host accessibility in this parasite community. Ovipositor structure could be a useful surrogate for predicting the biology of parasites in other communities.

Silicon oxycarbide (SiOC) glasses in the form of thin, dense, and crack‐free samples were fabricated according to the polymer pyrolysis route starting from cross‐linked polysiloxane. The amount of free carbon in the final SiOC materials was varied in the range 18‐60 vol%. The mechanical properties of the SiOC glasses were measured by nanoindentaion technique and revealed that both the Young's modulus and the hardness decrease with increase in the free carbon content and follow a simple rule of mixtures model.

This is a PDF file of an article that has undergone enhancements after acceptance, such as the addition of a cover page and metadata, and formatting for readability, but it is not yet the definitive version of record. This version will undergo additional copyediting, typesetting and review before it is published in its final form, but we are providing this version to give early visibility of the article. Please note that, during the production process, errors may be discovered which could affect the content, and all legal disclaimers that apply to the journal pertain.

Insect cuticle has drawn a lot of attention from engineers because of its multifunctional role in the life of insects. Some of these cuticles have an optimal combination of lightweight and good mechanical properties, and have inspired the design of composites with novel microstructures. Among these, beetle elytra have been explored extensively for their multilayered structure, multifunctional roles and mechanical properties. In this study, we investigated the bending properties of elytra by simulating their natural loading condition and comparing it with other loading configurations. Further, we examined the properties of their constitutive bulk layers to understand the contribution of each one to the overall mechanical behaviour. Our results showed that elytra are graded, multilayered composite structures that perform better in natural loading direction in terms of both flexural modulus and strength which is likely an adaptation to withstand loads encountered in the habitat. Experiments are supported by analytical calculations and finite element method modelling, which highlighted the additional role of the relatively stiff external exocuticle and of the flexible thin bottom layer in enhancing flexural mechanical properties. Such studies contribute to the knowledge of the mechanical behaviour of this natural composite material and to the development of novel bioinspired multifunctional composites and for optimized armours.

Mechanical properties of polymer‐derived ceramics are usually measured on samples pyrolyzed in inert atmosphere. Here, we report the hardness and elastic modulus of SiOC and SiCN pyrolyzed in both inert (Ar) and reactive (CO2) atmosphere. The external surface of the specimens exposed to the pyrolysis gas was characterized by Vickers microhardness measurements and infrared spectroscopy. The elastic modulus was evaluated by three‐point bending tests on thin (150‐200 µm) and dense specimens. Polished sections of the SiOC samples were prepared to study, by energy‐dispersive X‐ray spectroscopy (EDXS) and nanoindentation, how the elemental composition, hardness, and elastic modulus vary from the surface toward the bulk. For both compositions, pyrolysis in CO2 leads to a strong decrease in the hardness and elastic modulus. The hardness of both the samples pyrolyzed in CO2 approaches the typical value for fused silica, suggesting that CO2 selectively breaks the Si–C and Si–N bonds and leads to the formation of a silica‐like network. EDXS and nanoindentation reveal that the modification induced by the CO2 flow extends below the surface at least for a thickness of about 30 µm.

Development and characterization of porous scaffolds for tissue engineering and regenerative medicine is of great importance. In recent times, silk scaffolds were developed and successfully tested in tissue engineering and drug release applications. We developed a novel composite scaffold by mechanical infusion of silk hydrogel matrix into a highly porous network silk scaffold. The mechanical behaviour of these scaffolds was thoroughly examined for their possible use in load bearing applications. Firstly, unconfined compression experiments show that the denser composite scaffolds displayed significant enhancement in the elastic modulus as compared to either of the components. This effect was examined and further explained with the help of foam mechanics principles. Secondly, results from confined compression experiments that resemble loading of cartilage in confinement, showed nonlinear material responses for all scaffolds. Finally, the confined creep experiments were performed to calculate the hydraulic permeability of the scaffolds using soil mechanics principles. Our results show that composite scaffolds with some modifications can be a potential candidate for use of cartilage like applications. We hope such approaches help in developing novel scaffolds for tissue engineering by providing an understanding of the mechanics and can further be used to develop graded scaffolds by targeted infusion in specific regions.